Loading [MathJax]/jax/output/SVG/jax.js
Research article

Investigation of the mechanical properties of bio-composites based on loading kenaf fiber and molding process parameters

  • We aimed to obtain the mechanical properties of the resulting bio-composite material. Mechanical properties of bio-composite materials are greatly influenced by the fiber content and molding process parameters used. We used kenaf fiber as reinforcement and epoxy resin as a binder. Molding parameters such as molding time, molding pressure, and molding temperature were implemented to get the best bio-composite material. We used two types of kenaf fibers at content of 20 wt.%, which consisted of long fiber (first filler) and short fiber (second filler) as reinforcement, at compositions of 10:10, 12.5:7.5, 15:5, and 17.5:2.5 based on weight percentage (wt.%), respectively. Our results showed that the fiber content and molding process parameters used had a significant effect on the resulting mechanical properties. The highest flexural strength value was obtained at a fiber content of 5 wt.%, amounting to 44.77 MPa. By applying the molding process parameters, the flexural strength value obtained was successfully increased up to 58 MPa at a molding pressure of 270 kg/cm2. The scanning electron microscope (SEM) results showed that the fiber content of 5 wt.% could be distributed well throughout the matrix, as well as increasing the molding pressure successfully reducing the voids formed during the molding process of the resulting bio-composite material.

    Citation: Hendra Suherman, Yovial Mahyoedin, Afdal Zaky, Jarot Raharjo, Talitha Amalia Suherman, Irmayani Irmayani. Investigation of the mechanical properties of bio-composites based on loading kenaf fiber and molding process parameters[J]. AIMS Materials Science, 2024, 11(6): 1165-1178. doi: 10.3934/matersci.2024057

    Related Papers:

    [1] Ridha Dida, Hamid Boulares, Bahaaeldin Abdalla, Manar A. Alqudah, Thabet Abdeljawad . On positive solutions of fractional pantograph equations within function-dependent kernel Caputo derivatives. AIMS Mathematics, 2023, 8(10): 23032-23045. doi: 10.3934/math.20231172
    [2] Hamid Boulares, Manar A. Alqudah, Thabet Abdeljawad . Existence of solutions for a semipositone fractional boundary value pantograph problem. AIMS Mathematics, 2022, 7(10): 19510-19519. doi: 10.3934/math.20221070
    [3] Reny George, Fahad Al-shammari, Mehran Ghaderi, Shahram Rezapour . On the boundedness of the solution set for the ψ-Caputo fractional pantograph equation with a measure of non-compactness via simulation analysis. AIMS Mathematics, 2023, 8(9): 20125-20142. doi: 10.3934/math.20231025
    [4] Saeed M. Ali, Mohammed S. Abdo, Bhausaheb Sontakke, Kamal Shah, Thabet Abdeljawad . New results on a coupled system for second-order pantograph equations with ABC fractional derivatives. AIMS Mathematics, 2022, 7(10): 19520-19538. doi: 10.3934/math.20221071
    [5] Weerawat Sudsutad, Chatthai Thaiprayoon, Aphirak Aphithana, Jutarat Kongson, Weerapan Sae-dan . Qualitative results and numerical approximations of the (k,ψ)-Caputo proportional fractional differential equations and applications to blood alcohol levels model. AIMS Mathematics, 2024, 9(12): 34013-34041. doi: 10.3934/math.20241622
    [6] Choukri Derbazi, Zidane Baitiche, Mohammed S. Abdo, Thabet Abdeljawad . Qualitative analysis of fractional relaxation equation and coupled system with Ψ-Caputo fractional derivative in Banach spaces. AIMS Mathematics, 2021, 6(3): 2486-2509. doi: 10.3934/math.2021151
    [7] Abdelkader Moumen, Ramsha Shafqat, Zakia Hammouch, Azmat Ullah Khan Niazi, Mdi Begum Jeelani . Stability results for fractional integral pantograph differential equations involving two Caputo operators. AIMS Mathematics, 2023, 8(3): 6009-6025. doi: 10.3934/math.2023303
    [8] Iyad Suwan, Mohammed S. Abdo, Thabet Abdeljawad, Mohammed M. Matar, Abdellatif Boutiara, Mohammed A. Almalahi . Existence theorems for Ψ-fractional hybrid systems with periodic boundary conditions. AIMS Mathematics, 2022, 7(1): 171-186. doi: 10.3934/math.2022010
    [9] Mohamed Houas, Kirti Kaushik, Anoop Kumar, Aziz Khan, Thabet Abdeljawad . Existence and stability results of pantograph equation with three sequential fractional derivatives. AIMS Mathematics, 2023, 8(3): 5216-5232. doi: 10.3934/math.2023262
    [10] Karim Guida, Lahcen Ibnelazyz, Khalid Hilal, Said Melliani . Existence and uniqueness results for sequential ψ-Hilfer fractional pantograph differential equations with mixed nonlocal boundary conditions. AIMS Mathematics, 2021, 6(8): 8239-8255. doi: 10.3934/math.2021477
  • We aimed to obtain the mechanical properties of the resulting bio-composite material. Mechanical properties of bio-composite materials are greatly influenced by the fiber content and molding process parameters used. We used kenaf fiber as reinforcement and epoxy resin as a binder. Molding parameters such as molding time, molding pressure, and molding temperature were implemented to get the best bio-composite material. We used two types of kenaf fibers at content of 20 wt.%, which consisted of long fiber (first filler) and short fiber (second filler) as reinforcement, at compositions of 10:10, 12.5:7.5, 15:5, and 17.5:2.5 based on weight percentage (wt.%), respectively. Our results showed that the fiber content and molding process parameters used had a significant effect on the resulting mechanical properties. The highest flexural strength value was obtained at a fiber content of 5 wt.%, amounting to 44.77 MPa. By applying the molding process parameters, the flexural strength value obtained was successfully increased up to 58 MPa at a molding pressure of 270 kg/cm2. The scanning electron microscope (SEM) results showed that the fiber content of 5 wt.% could be distributed well throughout the matrix, as well as increasing the molding pressure successfully reducing the voids formed during the molding process of the resulting bio-composite material.



    Recently, fractional calculus methods became of great interest, because it is a powerful tool for calculating the derivation of multiples systems. These methods study real world phenomena in many areas of natural sciences including biomedical, radiography, biology, chemistry, and physics [1,2,3,4,5,6,7]. Abundant publications focus on the Caputo fractional derivative (CFD) and the Caputo-Hadamard derivative. Additionally, other generalization of the previous derivatives, such as Ψ-Caputo, study the existence of solutions to some FDEs (see [8,9,10,11,12,13,14]).

    In general, an m-point fractional boundary problem involves a fractional differential equation with fractional boundary conditions that are specified at m different points on the boundary of a domain. The fractional derivative is defined using the Riemann-Liouville fractional derivative or the Caputo fractional derivative. Solving these types of problems can be challenging due to the non-local nature of fractional derivatives. However, there are various numerical and analytical methods available for solving such problems, including the spectral method, the finite difference method, the finite element method, and the homotopy analysis method. The applications of m-point fractional boundary problems can be found in various fields, including physics, engineering, finance, and biology. These problems are useful in modeling and analyzing phenomena that exhibit non-local behavior or involve memory effects (see [15,16,17,18]).

    Pantograph equations are a set of differential equations that describe the motion of a pantograph, which is a mechanism used for copying and scaling drawings or diagrams. The equations are based on the assumption that the pantograph arms are rigid and do not deform during operation, we can simply say that see [19]. One important application of the pantograph equations is in the field of drafting and technical drawing. Before the advent of computer-aided design (CAD) software, pantographs were commonly used to produce scaled copies of drawings and diagrams. By adjusting the lengths of the arms and the position of the stylus, a pantograph can produce copies that are larger or smaller than the original [20], electrodynamics [21] and electrical pantograph of locomotive [22].

    Many authors studied a huge number of positive solutions for nonlinear fractional BVP using fixed point theorems (FPTs) such as SFPT, Leggett-Williams and Guo-Krasnosel'skii (see [23,24]). Some studies addressed the sign-changing of solution of BVPs [25,26,27,28,29].

    In this work, we use Schauder's fixed point theorem (SFPT) to solve the semipostone multipoint Ψ-Caputo fractional pantograph problem

    Dν;ψrϰ(ς)+F(ς,ϰ(ς),ϰ(r+λς))=0, ς in (r,) (1.1)
    ϰ(r)=ϑ1, ϰ()=m2i=1ζiϰ(ηi)+ϑ2, ϑiR, i{1,2}, (1.2)

    where λ(0,r),Dν;ψr is Ψ-Caputo fractional derivative (Ψ-CFD) of order ν, 1<ν2, ζiR+(1im2) such that 0<Σm2i=1ζi<1, ηi(r,), and F:[r,]×R×RR.

    The most important aspect of this research is to prove the existence of a positive solution of the above m-point FBVP. Note that in [30], the author considered a two-point BVP using Liouville-Caputo derivative.

    The article is organized as follows. In the next section, we provide some basic definitions and arguments pertinent to fractional calculus (FC). Section 3 is devoted to proving the the main result and an illustrative example is given in Section 4.

    In the sequel, Ψ denotes an increasing map Ψ:[r1,r2]R via Ψ(ς)0, ς, and [α] indicates the integer part of the real number α.

    Definition 2.1. [4,5] Suppose the continuous function ϰ:(0,)R. We define (RLFD) the Riemann-Liouville fractional derivative of order α>0,n=[α]+1 by

    RLDα0+ϰ(ς)=1Γ(nα)(ddς)nς0(ςτ)nα1ϰ(τ)dτ,

    where n1<α<n.

    Definition 2.2. [4,5] The Ψ-Riemann-Liouville fractional integral (Ψ-RLFI) of order α>0 of a continuous function ϰ:[r,]R is defined by

    Iα;Ψrϰ(ς)=ςr(Ψ(ς)Ψ(τ))α1Γ(α)Ψ(τ)ϰ(τ)dτ.

    Definition 2.3. [4,5] The CFD of order α>0 of a function ϰ:[0,+)R is defined by

    Dαϰ(ς)=1Γ(nα)ς0(ςτ)nα1ϰ(n)(τ)dτ, α(n1,n),nN.

    Definition 2.4. [4,5] We define the Ψ-CFD of order α>0 of a continuous function ϰ:[r,]R by

    Dα;Ψrϰ(ς)=ςr(Ψ(ς)Ψ(τ))nα1Γ(nα)Ψ(τ)nΨϰ(τ)dτ, ς>r, α(n1,n),

    where nΨ=(1Ψ(ς)ddς)n,nN.

    Lemma 2.1. [4,5] Suppose q,>0, and ϰinC([r,],R). Then ς[r,] and by assuming Fr(ς)=Ψ(ς)Ψ(r), we have

    1) Iq;ΨrI;Ψrϰ(ς)=Iq+;Ψrϰ(ς),

    2) Dq;ΨrIq;Ψrϰ(ς)=ϰ(ς),

    3) Iq;Ψr(Fr(ς))1=Γ()Γ(+q)(Fr(ς))+q1,

    4) Dq;Ψr(Fr(ς))1=Γ()Γ(q)(Fr(ς))q1,

    5) Dq;Ψr(Fr(ς))k=0, k=0,,n1, nN, qin(n1,n].

    Lemma 2.2. [4,5] Let n1<α1n,α2>0, r>0, ϰL(r,), Dα1;ΨrϰL(r,). Then the differential equation

    Dα1;Ψrϰ=0

    has the unique solution

    ϰ(ς)=W0+W1(Ψ(ς)Ψ(r))+W2(Ψ(ς)Ψ(r))2++Wn1(Ψ(ς)Ψ(r))n1,

    and

    Iα1;ΨrDα1;Ψrϰ(ς)=ϰ(ς)+W0+W1(Ψ(ς)Ψ(r))+W2(Ψ(ς)Ψ(r))2++Wn1(Ψ(ς)Ψ(r))n1,

    with WR, {0,1,,n1}.

    Furthermore,

    Dα1;ΨrIα1;Ψrϰ(ς)=ϰ(ς),

    and

    Iα1;ΨrIα2;Ψrϰ(ς)=Iα2;ΨrIα1;Ψrϰ(ς)=Iα1+α2;Ψrϰ(ς).

    Here we will deal with the FDE solution of (1.1) and (1.2), by considering the solution of

    Dν;ψrϰ(ς)=h(ς), (2.1)

    bounded by the condition (1.2). We set

    Δ:=Ψ()Ψ(r)Σm2i=1ζi(Ψ(ηi)Ψ(r)).

    Lemma 2.3. Let ν(1,2] and ς[r,]. Then, the FBVP (2.1) and (1.2) have a solution ϰ of the form

    ϰ(ς)=[1+Σm2i=1ζi1Δ(Ψ(ς)Ψ(r))]ϑ1+Ψ(ς)Ψ(r)Δϑ2+rϖ(ς,τ)h(τ)Ψ(τ)dτ,

    where

    ϖ(ς,τ)=1Γ(ν){[(Ψ()Ψ(r))ν1Σm2j=iζj(Ψ(ηj)Ψ(τ))ν1]Ψ(ς)Ψ(r)Δ(Ψ(ς)Ψ(τ))ν1,τς,ηi1<τηi,[(Ψ()Ψ(τ))ν1Σm2j=iζj(Ψ(ηj)Ψ(τ))ν1]Ψ()Ψ(r)Δ,ςτ,ηi1<τηi, (2.2)

    i=1,2,...,m2.

    Proof. According to the Lemma 2.2 the solution of Dν;ψrϰ(ς)=h(ς) is given by

    ϰ(ς)=1Γ(ν)ςr(Ψ(ς)Ψ(τ))ν1h(τ)Ψ(τ)dτ+c0+c1(Ψ(ς)Ψ(r)), (2.3)

    where c0,c1R. Since ϰ(r)=ϑ1 and ϰ()=m2i=1ζiϰ(ηi)+ϑ2, we get c0=ϑ1 and

    c1=1Δ(1Γ(ν)m2i=1ζiηjr(Ψ(ηi)Ψ(τ))ν1h(τ)Ψ(τ)dτ+1Γ(ν)r(Ψ()Ψ(τ))ν1h(τ)Ψ(τ)dτ+ϑ1[m2i=1ζi1]+ϑ2).

    By substituting c0,c1 into Eq (2.3) we find,

    ϰ(ς)=[1+Σm2i=1ζi1Δ(Ψ(ς)Ψ(r))]ϑ1+(Ψ(ς)Ψ(r))Δϑ21Γ(ν)(ςr(Ψ(ς)Ψ(τ))ν1h(τ)Ψ(τ)dτ+(Ψ(ς)Ψ(r))Δm2i=1ζiηjr(Ψ(ηi)Ψ(τ))ν1h(τ)Ψ(τ)dτΨ(ς)Ψ(r)Δr(Ψ()Ψ(τ))ν1h(τ)Ψ(τ)dτ)=[1+Σm2i=1ζi1Δ(Ψ(ς)Ψ(r))]ϑ1+(Ψ(ς)Ψ(r))Δϑ2+rϖ(ς,τ)h(τ)Ψ(τ)dτ,

    where ϖ(ς,τ) is given by (2.2). Hence the required result.

    Lemma 2.4. If 0<m2i=1ζi<1, then

    i) Δ>0,

    ii) (Ψ()Ψ(τ))ν1m2j=iζj(Ψ(ηj)Ψ(τ))ν1>0.

    Proof. i) Since ηi<, we have

    ζi(Ψ(ηi)Ψ(r))<ζi(Ψ()Ψ(r)),
    m2i=1ζi(Ψ(ηi)Ψ(r))>m2i=1ζi(Ψ()Ψ(r)),
    Ψ()Ψ(r)m2i=1ζi(Ψ(ηi)Ψ(r))>Ψ()Ψ(r)m2i=1ζi(Ψ()Ψ(r))=(Ψ()Ψ(r))[1m2i=1ζi].

    If 1Σm2i=1ζi>0, then (Ψ()Ψ(r))Σm2i=1ζi(Ψ(ηi)Ψ(r))>0. So we have Δ>0.

    ii) Since 0<ν11, we have (Ψ(ηi)Ψ(τ))ν1<(Ψ()Ψ(τ))ν1. Then we obtain

    m2j=iζj(Ψ(ηj)Ψ(τ))ν1<m2j=iζj(Ψ()Ψ(τ))ν1(Ψ()Ψ(τ))ν1m2i=1ζi<(Ψ()Ψ(τ))ν1,

    and so

    (Ψ()Ψ(τ))ν1m2j=iζj(Ψ(ηj)Ψ(τ))ν1>0.

    Remark 2.1. Note that rϖ(ς,τ)Ψ(τ)dτ is bounded ς[r,]. Indeed

    r|ϖ(ς,τ)|Ψ(τ)dτ1Γ(ν)ςr(Ψ(ς)Ψ(τ))ν1Ψ(τ)dτ+Ψ(ς)Ψ(r)Γ(ν)Δm2i=1ζiηir(Ψ(ηj)Ψ(τ))ν1Ψ(τ)dτ+Ψ(ς)Ψ(r)ΔΓ(ν)r(Ψ()Ψ(τ))ν1Ψ(τ)dτ=(Ψ(ς)Ψ(r))νΓ(ν+1)+Ψ(ς)Ψ(r)ΔΓ(ν+1)m2i=1ζi(Ψ(ηi)Ψ(r))ν+Ψ(ς)Ψ(r)ΔΓ(ν+1)(Ψ()Ψ(r))ν(Ψ()Ψ(r))νΓ(ν+1)+Ψ()Ψ(r)ΔΓ(ν+1)m2i=1ζi(Ψ(ηi)Ψ(r))ν+(Ψ()Ψ(r))ν+1ΔΓ(ν+1)=M. (2.4)

    Remark 2.2. Suppose Υ(ς)L1[r,], and w(ς) verify

    {Dν;ψrw(ς)+Υ(ς)=0,w(r)=0, w()=Σm2i=1ζiw(ηi), (2.5)

    then w(ς)=rϖ(ς,τ)Υ(τ)Ψ(τ)dτ.

    Next we recall the Schauder fixed point theorem.

    Theorem 2.1. [23] [SFPT] Consider the Banach space Ω. Assume bounded, convex, closed subset in Ω. If ϝ: is compact, then it has a fixed point in .

    We start this section by listing two conditions which will be used in the sequel.

    (Σ1) There exists a nonnegative function ΥL1[r,] such that rΥ(ς)dς>0 and F(ς,ϰ,v)Υ(ς) for all (ς,ϰ,v)[r,]×R×R.

    (Σ2) G(ς,ϰ,v)0, for (ς,ϰ,v)[r,]×R×R.

    Let =C([r,],R) the Banach space of CFs (continuous functions) with the following norm

    ϰ=sup{|ϰ(ς)|:ς[r,]}.

    First of all, it seems that the FDE below is valid

    Dν;ψrϰ(ς)+G(ς,ϰ(ς),ϰ(r+λς))=0, ς[r,]. (3.1)

    Here the existence of solution satisfying the condition (1.2), such that G:[r,]×R×RR

    G(ς,z1,z2)={F(ς,z1,z2)+Υ(ς), z1,z20,F(ς,0,0)+Υ(ς), z10 or z20, (3.2)

    and ϰ(ς)=max{(ϰw)(ς),0}, hence the problem (2.5) has w as unique solution. The mapping Q: accompanied with the (3.1) and (1.2) defined as

    (Qϰ)(ς)=[1+Σm2i=1ζi1Δ(Ψ(ς)Ψ(r))]ϑ1+Ψ(ς)Ψ(r)Δϑ2+rϖ(ς,τ)G(ς,ϰ(τ),ϰ(r+λτ))Ψ(τ)dτ, (3.3)

    where the relation (2.2) define ϖ(ς,τ). The existence of solution of the problems (3.1) and (1.2) give the existence of a fixed point for Q.

    Theorem 3.1. Suppose the conditions (Σ1) and (Σ2) hold. If there exists ρ>0 such that

    [1+Σm2i=1ζi1Δ(Ψ()Ψ(r))]ϑ1+Ψ()Ψ(r)Δϑ2+LMρ,

    where Lmax{|G(ς,ϰ,v)|:ς[r,], |ϰ|,|v|ρ} and M is defined in (2.4), then, the problems (3.1) and (3.2) have a solution ϰ(ς).

    Proof. Since P:={ϰ:ϰρ} is a convex, closed and bounded subset of B described in the Eq (3.3), the SFPT is applicable to P. Define Q:P by (3.3). Clearly Q is continuous mapping. We claim that range of Q is subset of P. Suppose ϰP and let ϰ(ς)ϰ(ς)ρ, ς[r,]. So

    |Qϰ(ς)|=|[1+Σm2i=1ζi1Δ(Ψ(ς)Ψ(r))]ϑ1+Ψ(ς)Ψ(r)Δϑ2+rϖ(ς,τ)G(τ,ϰ(τ),ϰ(r+λτ))Ψ(τ)dτ|[1+Σm2i=1ζi1Δ(Ψ()Ψ(r))]ϑ1+Ψ()Ψ(r)Δϑ2+LMρ,

    for all ς[r,]. This indicates that Qϰρ, which proves our claim. Thus, by using the Arzela-Ascoli theorem, Q: is compact. As a result of SFPT, Q has a fixed point ϰ in P. Hence, the problems (3.1) and (1.2) has ϰ as solution.

    Lemma 3.1. ϰ(ς) is a solution of the FBVP (1.1), (1.2) and ϰ(ς)>w(ς) for every ς[r,] iff the positive solution of FBVP (3.1) and (1.2) is ϰ=ϰ+w.

    Proof. Let ϰ(ς) be a solution of FBVP (3.1) and (1.2). Then

    ϰ(ς)=[1+Σm2i=1ζi1Δ(Ψ(ς)Ψ(r))]ϑ1+(Ψ(ς)Ψ(r))Δϑ2+1Γ(ν)rϖ(ς,τ)G(τ,ϰ(τ),ϰ(r+λτ))Ψ(τ)dτ=[1+Σm2i=1ζi1Δ(Ψ(ς)Ψ(r))]ϑ1+Ψ(ς)Ψ(r)Δϑ2+1Γ(ν)rϖ(ς,τ)(F(τ,ϰ(τ),ϰ(r+λτ))+p(τ))Ψ(τ)dτ=[1+Σm2i=1ζi1Δ(Ψ(ς)Ψ(r))]ϑ1+Ψ(ς)Ψ(r)Δϑ2+1Γ(ν)rϖ(ς,τ)F(τ,(ϰw)(τ),(ϰw)(r+λτ))Ψ(τ)dτ+1Γ(ν)rϖ(ς,τ)p(τ)Ψ(τ)dτ=[1+Σm2i=1ζi1Δ(Ψ(ς)Ψ(r))]ϑ1+Ψ(ς)Ψ(r)Δϑ2+1Γ(ν)rϖ(ς,τ)G(τ,(ϰw)(τ),(ϰw)(r+λτ))Ψ(τ)dτ+w(ς).

    So,

    ϰ(ς)w(ς)=[1+Σm2i=1ζi1Δ(Ψ(ς)Ψ(r))]ϑ1+Ψ(ς)Ψ(r)Δϑ2+1Γ(ν)rϖ(ς,τ)F(τ,(ϰw)(τ),(ϰw)(r+λτ))Ψ(τ)dτ.

    Then we get the existence of the solution with the condition

    ϰ(ς)=[1+Σm2i=1ζi1Δ(Ψ(ς)Ψ(r))]ϑ1+Ψ(ς)Ψ(r)Δϑ2+1Γ(ν)rϖ(ς,τ)F(τ,ϰ(τ),ϰ(r+λτ))Ψ(τ)dτ.

    For the converse, if ϰ is a solution of the FBVP (1.1) and (1.2), we get

    Dν;ψr(ϰ(ς)+w(ς))=Dν;ψrϰ(ς)+Dν;ψrw(ς)=F(ς,ϰ(ς),ϰ(r+λς))p(ς)=[F(ς,ϰ(ς),ϰ(r+λς))+p(ς)]=G(ς,ϰ(ς),ϰ(r+λς)),

    which leads to

    Dν;ψrϰ(ς)=G(ς,ϰ(ς),ϰ(r+λς)).

    We easily see that

    ϰ(r)=ϰ(r)w(r)=ϰ(r)0=ϑ1,

    i.e., ϰ(r)=ϑ1 and

    ϰ()=m2i=1ζiϰ(ηi)+ϑ2,
    ϰ()w()=m2i=1ζiϰ(ηi)m2i=1ζjw(ηi)+ϑ2=m2i=1ζi(ϰ(ηi)w(ηi))+ϑ2.

    So,

    ϰ()=m2i=1ζiϰ(ηi)+ϑ2.

    Thus ϰ(ς) is solution of the problem FBVP (3.1) and (3.2).

    We propose the given FBVP as follows

    D75ϰ(ς)+F(ς,ϰ(ς),ϰ(1+0.5ς))=0, ς(1,e), (4.1)
    ϰ(1)=1, ϰ(e)=17ϰ(52)+15ϰ(74)+19ϰ(115)1. (4.2)

    Let Ψ(ς)=logς, where F(ς,ϰ(ς),ϰ(1+12ς))=ς1+ςarctan(ϰ(ς)+ϰ(1+12ς)).

    Taking Υ(ς)=ς we get e1ςdς=e212>0, then the hypotheses (Σ1) and (Σ2) hold. Evaluate Δ0.366, M3.25 we also get |G(ς,ϰ,v)|<π+e=L such that |ϰ|ρ, ρ=17, we could just confirm that

    [1+Σm2i=1ζi1Δ(Ψ()Ψ(r))]ϑ1+Ψ()Ψ(r)Δϑ2+LM16.3517. (4.3)

    By applying the Theorem 3.1 there exit a solution ϰ(ς) of the problem (4.1) and (4.2).

    In this paper, we have provided the proof of BVP solutions to a nonlinear Ψ-Caputo fractional pantograph problem or for a semi-positone multi-point of (1.1) and(1.2). What's new here is that even using the generalized Ψ-Caputo fractional derivative, we were able to explicitly prove that there is one solution to this problem, and that in our findings, we utilize the SFPT. The results obtained in our work are significantly generalized and the exclusive result concern the semi-positone multi-point Ψ-Caputo fractional differential pantograph problem (1.1) and (1.2).

    The authors extend their appreciation to the Deanship of Scientific Research at King Khalid University for funding this work through Small Groups (RGP.1/350/43).

    The authors declare no conflict of interest.



    [1] Natrayan L, Merneedi A (2020) Experimental investigation on wear behaviour of bio-waste reinforced fusion fiber composite laminate under various conditions. Mater Today Proc 37: 1486–1490. https://doi.org/10.1016/j.matpr.2020.07.108 doi: 10.1016/j.matpr.2020.07.108
    [2] Akil HM, Omar MF, Mazuki AAM, et al. (2011) Kenaf fiber reinforced composites: A review. Mater Des 32: 4107–4121. https://doi.org/10.1016/j.matdes.2011.04.008 doi: 10.1016/j.matdes.2011.04.008
    [3] Austin CC, Mondell CN, Clark DG, et al. (2024) Kenaf: Opportunities for an ancient fiber crop. Agronomy 14: 1542–2024. https://doi.org/10.3390/agronomy14071542 doi: 10.3390/agronomy14071542
    [4] Raja T, Munuswamy DB, Francis RR, et al. (2024) Experimental investigations on the effect of palm oil in kenaf fibre-reinforced basalt particulate hybrid biocomposite. Biomass Conv Bioref 14: 5345–5355. https://doi.org/10.1007/s13399-022-02714-8 doi: 10.1007/s13399-022-02714-8
    [5] Kabir MM, Wang H, Lau KT, et al. (2012) Chemical treatments on plant-based natural fibre reinforced polymer composites: An overview. Compos Part B Eng 43: 2883–2892. https://doi.org/10.1016/j.compositesb.2012.04.053 doi: 10.1016/j.compositesb.2012.04.053
    [6] Singh JIP, Sharma P, Singh S, et al. (2024) Impact of molding temperature, fiber loading and chemical modifications on the physicomechanical, and microstructural morphology properties of woven kenaf fiber/PLA composites for non-structural applications. J Nat Fibers 21: 2326586. https://doi.org/10.1080/15440478.2024.2326586 doi: 10.1080/15440478.2024.2326586
    [7] Li M, Pu Y, Thomas VM, et al. (2020) Recent advancements of plant-based natural fiber-reinforced composites and their applications. Compos Part B Eng 200: 108254. https://doi.org/10.1016/j.compositesb.2020.108254 doi: 10.1016/j.compositesb.2020.108254
    [8] Naskar AK, Keum JK, Boeman RG (2016) Polymer matrix nanocomposites for automotive structural components. Nat Nanotechnol 11: 1026–1030. https://doi.org/10.1038/nnano.2016.262 doi: 10.1038/nnano.2016.262
    [9] Braga RA, Magalhaes PAA (2015) Analysis of the mechanical and thermal properties of jute and glass fiber as reinforcement epoxy hybrid composites. Mater Sci Eng C 56: 269–273. https://doi.org/10.1016/j.msec.2015.06.031 doi: 10.1016/j.msec.2015.06.031
    [10] Ibrahim NA, Hadithon KA, Abdan K (2010) Effect of fiber treatment on mechanical properties of kenaf fiber-ecoflex composites. J Reinf Plast Compos 29: 2192–2198. https://doi.org/10.1177/0731684409347592 doi: 10.1177/0731684409347592
    [11] Gupta MK (2018) Thermal and dynamic mechanical analysis of hybrid jute/sisal fibre reinforced epoxy composite. Proc Inst Mech Eng Part L 232: 743–748. https://doi.org/10.1177/1464420716646398 doi: 10.1177/1464420716646398
    [12] Ismail AS, Jawaid M, Naveen J (2019) Void content, tensile, vibration and acoustic properties of kenaf/bamboo fiber reinforced epoxy hybrid composites. Materials 12: 2094. https://doi.org/10.3390/ma12132094 doi: 10.3390/ma12132094
    [13] Anand PB, Nagaraja S, Jayaram L, et al. (2023) Kenaf fiber and hemp fiber multi-walled carbon nanotube filler-reinforced epoxy-based hybrid composites for biomedical applications: Morphological and mechanical characterization. J Compos Sci 7: 328. https://doi.org/10.3390/jcs7080324 doi: 10.3390/jcs7080324
    [14] Davoodi MM, Sapuan SM, Ahmad D, et al. (2010) Mechanical properties of hybrid kenaf/glass reinforced epoxy composite for passenger car bumper beam. Mater Des 31: 4927–4932. https://doi.org/10.1016/j.matdes.2010.05.021 doi: 10.1016/j.matdes.2010.05.021
    [15] Mohammed M, Betar BO, Rahman R, et al. (2019) Zinc oxide nano particles integrated kenaf/unsaturated polyester biocomposite. J Renew Mater 7: 967–982. https://doi.org/10.32604/jrm.2019.07562 doi: 10.32604/jrm.2019.07562
    [16] Saba N, Paridah MT, Abdan K, et al. (2016) Effect of oil palm nano filler on mechanical and morphological properties of kenaf reinforced epoxy composites. Constr Build Mater 123: 15–26. https://doi.org/10.1016/j.conbuildmat.2016.06.131 doi: 10.1016/j.conbuildmat.2016.06.131
    [17] Mohd Radzuan NA, Tholibon D, Sulong AB, et al. (2019) New processing technique for biodegradable kenaf composites: A simple alternative to commercial automotive parts. Compos Part B Eng 184: 107644. https://doi.org/10.1016/j.compositesb.2019.107644 doi: 10.1016/j.compositesb.2019.107644
    [18] Ghabezi P, Farahani M, Hosseini Fakhr M, et al. (2016) Investigation of mechanical behavior of alfa and gamma nano-alumina/epoxy composite made by vartm. Int J Adv Biotechnol Res 7: 731–736.
    [19] Xia C, Ren H, Shi SQ, et al. (2015) Natural fiber composites with EMI shielding function fabricated using VARTM and Cu film magnetron sputtering. Appl Surf Sci 362: 335–340. https://doi.org/10.1016/j.apsusc.2015.11.202 doi: 10.1016/j.apsusc.2015.11.202
    [20] Rassmann S, Reid RG, Paskaramoorthy R (2010) Effects of processing conditions on the mechanical and water absorption properties of resin transfer moulded kenaf fibre reinforced polyester composite laminates. Compos Part A Appl Sci Manuf 41: 1612–1619. https://doi.org/10.1016/j.compositesa.2010.07.009 doi: 10.1016/j.compositesa.2010.07.009
    [21] Kenaf M, National Tobacco Board (NKTB) (2024) Kenaf fiber. Available from: https://www.kenafmall.com/index.php (accessed Apr. 10, 2024).
    [22] Composites US (2024) Epoxy resin. Available from: https://www.uscomposites.com/epoxy.html(accessed May 10, 2024).
    [23] Naveen ERKJ, Karthikeyan N, Khan T, et al. (2024) Effect of cellulose nanocrystals on the mechanical and free vibration behavior of hybrid glass/kenaf fiber reinforced polyurethane core-based sandwich structures. J Nat Fibers 21: 7–14. https://doi.org/10.1080/15440478.2024.2361311 doi: 10.1080/15440478.2024.2361311
    [24] Rahman M, Islam MN, Ara MA, et al. (20204) Mechanical properties of kenaf and palmyra palm leaf stalk fiber reinforced composite. Results Surf Interfaces 15: 100229. https://doi.org/10.1016/j.rsurfi.2024.100229
    [25] Muralidharan ND, Subramanian J, Mary JJ, et al. (2024) An experimental study on the low-elocity impact behavior of biopolymer-coated kenaf fiber reinforced epoxy nanocomposites: A route to sustainability. Mater Circ Econ 6: 20. https://doi.org/10.1007/s42824-024-00110-3 doi: 10.1007/s42824-024-00110-3
    [26] Asim M, Jawaid M, Nasir M, et al (2018) Effect of fiber loadings and treatment on dynamic mechanical, thermal and flammability properties of pineapple leaf fiber and kenaf phenolic composites. J Renew Mater 6: 383–393. https://doi.org/10.7569/JRM.2017.634162 doi: 10.7569/JRM.2017.634162
    [27] Mohanty AK, Misra M, Hinrichsen G (2000) Biofibres, biodegradable polymers and biocomposites: An overview. Macromol Mater Eng 276–277: 1–24. https://doi.org/10.1002/(SICI)1439-2054(20000301)276:1<1::AID-MAME1>3.0.CO;2-W doi: 10.1002/(SICI)1439-2054(20000301)276:1<1::AID-MAME1>3.0.CO;2-W
    [28] Suherman H, Aksa K, Mahyoedin Y, et al. (2021) The effect of different fibre lengths on the mechanical properties of biocomposites. Mater Plast 58: 216–221. https://doi.org/10.37358/MP.21.4.5547 doi: 10.37358/MP.21.4.5547
    [29] Webber CLI, Bledsoe VK (2002) Kenaf yield components and plant composition. Trends New Crop New Uses 348–357.
    [30] Boopalan M, Niranjanaa M, Umapathy MJ (2013) Study on the mechanical properties and thermal properties of jute and banana fiber reinforced epoxy hybrid composites. Compos Part B Eng 51: 54–57. https://doi.org/10.1016/j.compositesb.2013.02.033 doi: 10.1016/j.compositesb.2013.02.033
    [31] Zhou Y, Fan M, Chen L (2016) Interface and bonding mechanisms of plant fibre composites: An overview. Compos Part B Eng 101: 31–45. https://doi.org/10.1016/j.compositesb.2016.06.055 doi: 10.1016/j.compositesb.2016.06.055
  • Reader Comments
  • © 2024 the Author(s), licensee AIMS Press. This is an open access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0)
通讯作者: 陈斌, bchen63@163.com
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索

Metrics

Article views(681) PDF downloads(59) Cited by(0)

Figures and Tables

Figures(7)  /  Tables(1)

/

DownLoad:  Full-Size Img  PowerPoint
Return
Return

Catalog