Performance evaluation of solar still integrated with thermoelectric heat pump system

Fouad Alkilani; Ouassini Nemraoui; Fareed Ismail; Fouad Alkilani; Ouassini Nemraoui; Fareed Ismail

doi:10.3934/energy.2023003

AIMS Energy

2023, Volume 11, Issue 1: 47-63. doi: 10.3934/energy.2023003

Previous Article Next Article

Research article Special Issues

Performance evaluation of solar still integrated with thermoelectric heat pump system

Mechanical Engineering Department, Cape Peninsula University of Technology (CPUT), Cape Town, South Africa

Received: 28 August 2022 Revised: 13 January 2023 Accepted: 31 January 2023 Published: 10 February 2023

This research presents a method for improving a conventional solar still to produce potable water during adverse conditions where there is low or no solar radiation. Summer and winter conditions in the Western Cape province of South Africa were considered. A comparative experimental study was conducted between a conventional solar still and the developed solar still. The developed solar still incorporated a photovoltaic powered thermoelectric heat pump. The purpose of the thermoelectric (TE) heat pump was to accelerate convection inside the developed solar still assembly. The coefficient of performance (COP) of the thermoelectric heat pump installed in the developed solar still ranged from 0.4 to 1.9 at an input current of 5 A. The results indicated that the developed solar still was able to produce 2300 mL per day of drinkable water during a good day in the winter, but the conventional solar still was only able to produce 650 mL per day. The developed solar still produced 2180 mL per day, whereas the ordinary solar still produced 1050 mL per day, during a mild summer day. The developed still had an accumulated water production of 1180 mL during a night with mild temperatures. This significant improvement in yield of the developed solar still system is due to the change in temperature difference between the glazing and the water surface within the developed solar still. This is a significant contribution to the technology of solar water purification.
- solar distillation,
- solar still,
- thermoelectric heat pump
Citation: Fouad Alkilani, Ouassini Nemraoui, Fareed Ismail. Performance evaluation of solar still integrated with thermoelectric heat pump system[J]. AIMS Energy, 2023, 11(1): 47-63. doi: 10.3934/energy.2023003

Related Papers:

Abstract

This research presents a method for improving a conventional solar still to produce potable water during adverse conditions where there is low or no solar radiation. Summer and winter conditions in the Western Cape province of South Africa were considered. A comparative experimental study was conducted between a conventional solar still and the developed solar still. The developed solar still incorporated a photovoltaic powered thermoelectric heat pump. The purpose of the thermoelectric (TE) heat pump was to accelerate convection inside the developed solar still assembly. The coefficient of performance (COP) of the thermoelectric heat pump installed in the developed solar still ranged from 0.4 to 1.9 at an input current of 5 A. The results indicated that the developed solar still was able to produce 2300 mL per day of drinkable water during a good day in the winter, but the conventional solar still was only able to produce 650 mL per day. The developed solar still produced 2180 mL per day, whereas the ordinary solar still produced 1050 mL per day, during a mild summer day. The developed still had an accumulated water production of 1180 mL during a night with mild temperatures. This significant improvement in yield of the developed solar still system is due to the change in temperature difference between the glazing and the water surface within the developed solar still. This is a significant contribution to the technology of solar water purification.

References

[1]	Liang R, Hu A, Hatat-Fraile M, et al. (2014) Fundamentals on adsorption, membrane filtration, and advanced oxidation processes for water treatment. In: Nanotechnology for Water Treatment and Purification, Knoxville, Springer, 1-45. https://doi.org/10.1007/978-3-319-06578-6_1
[2]	Cheremisinoff NP (2002) Handbook of Water and Wastewater Treatment Technologies, 1st ed., Woburn—USA: Butterworth-Heinemann, 2002. https://doi.org/10.1016/B978-075067498-0/50004-8
[3]	Bundschuh J, Kaczmarczyk M, Ghaffour N, et al. (2021) State-of-the-art of renewable energy sources used in water desalination: Present and future prospects. Desalination 508: 115035. https://doi.org/10.1016/j.desal.2021.115035 doi: 10.1016/j.desal.2021.115035
[4]	Misdan N, Lau WJ, Ismail AF (2012) Seawater Reverse Osmosis (SWRO) desalination by thin-film composite membrane—Current development, challenges and future prospects. Desalination: 228-237. https://doi.org/10.1016/j.desal.2011.11.001
[5]	Darre NC, Toor GS (2018) Desalination of water: A review. Curr Pollut Rep 4: 104-111. https://doi.org/10.1007/s40726-018-0085-9 doi: 10.1007/s40726-018-0085-9
[6]	Elsaid K, Kamil M, Sayed ET, et al. (2020) Environmental impact of desalination technologies: A review. Sci Total Environ 748: 141528. https://doi.org/10.1016/j.scitotenv.2020.141528 doi: 10.1016/j.scitotenv.2020.141528
[7]	Jones E, Qadir M, van Vliet, et al. (2019) The state of desalination and brine production: A global outlook. Sci Total Environ 657: 1343-1356. https://doi.org/10.1016/j.scitotenv.2018.12.076 doi: 10.1016/j.scitotenv.2018.12.076
[8]	Shahabi MP, McHugh A, Anda M, et al. (2017) A framework for planning sustainable seawater desalination water supply. Sci Total Environ 575: 826-835. https://doi.org/10.1016/j.scitotenv.2016.09.136 doi: 10.1016/j.scitotenv.2016.09.136
[9]	Lattemann S, Höpner T (2008) Environmental impact and impact assessment of seawater desalination. Desalination 220: 1-15. https://doi.org/10.1016/j.desal.2007.03.009 doi: 10.1016/j.desal.2007.03.009
[10]	Zhang Y, Sivakumar M, Yang S, et al. (2018) Application of solar energy in water treatment processes: A review. Desalination 428: 116-145. https://doi.org/10.1016/j.desal.2017.11.020 doi: 10.1016/j.desal.2017.11.020
[11]	Huang W, Su P, Cao Y, et al. (2020) Three-dimensional hierarchical CuxS-based evaporator for high-efficiency multifunctional solar distillation. Nano Energy 69: 104465. https://doi.org/10.1016/j.nanoen.2020.104465 doi: 10.1016/j.nanoen.2020.104465
[12]	Tiwari GN, Sahota L (2017) Advanced solar-distillation systems: basic principles, thermal modeling, and its application. Springer. Available from: https://www.amazon.com/Advanced-Solar-Distillation-Systems-Principles-Application/dp/9811046719.
[13]	Peng G, Sharshir SW, Hu Z, et al. (2021) A compact flat solar still with high performance. Int J Heat Mass Transfer 179: 121657. https://doi.org/10.1016/j.ijheatmasstransfer.2021.121657 doi: 10.1016/j.ijheatmasstransfer.2021.121657
[14]	Bhardwaj R, Ten Kortenaar MV, Mudde RF (2015) Maximized production of water by increasing area of condensation surface for solar distillation. Appl Energy 154: 480-490. https://doi.org/10.1016/j.apenergy.2015.05.060 doi: 10.1016/j.apenergy.2015.05.060
[15]	Mohamed AF, Hegazi AA, Sultan GI, et al. (2019) Augmented heat and mass transfer effect on performance of a solar still using porous absorber: Experimental investigation and exergetic analysis. Appl Therm Eng 150: 1206-1215. https://doi.org/10.1016/j.applthermaleng.2019.01.070 doi: 10.1016/j.applthermaleng.2019.01.070
[16]	Bataineh KM, Abbas MA (2020) Performance analysis of solar still integrated with internal reflectors and fins. Sol Energy 205: 22-36. https://doi.org/10.1016/j.solener.2020.04.059 doi: 10.1016/j.solener.2020.04.059
[17]	Porta-Gándara MA, Fernández-Zayas JL, Chargoy-del-Valle N (2020) Solar still distillation enhancement through water surface perturbation. Sol Energy 196: 312-318. https://doi.org/10.1016/j.solener.2019.12.028 doi: 10.1016/j.solener.2019.12.028
[18]	Jani HK, Modi KV (2019) Experimental performance evaluation of single basin dual slope solar still with circular and square cross-sectional hollow fins. Sol Energy 179: 186-194. https://doi.org/10.1016/j.solener.2018.12.054 doi: 10.1016/j.solener.2018.12.054
[19]	Kabeel AE, Abdelgaied M (2020) Enhancement of pyramid-shaped solar stills performance using a high thermal conductivity absorber plate and cooling the glass cover. Renewable Energy 146: 769-775. https://doi.org/10.1016/j.renene.2019.07.020 doi: 10.1016/j.renene.2019.07.020
[20]	Esfe MH, Esfandeh S, Toghraie D (2021) Optimization of influential geometrical parameters of single slope solar still equipped with thermoelectric system to achieve maximum desalinated water. Energy Rep 7: 5257-5268. https://doi.org/10.1016/j.egyr.2021.08.106 doi: 10.1016/j.egyr.2021.08.106
[21]	Esfe MH, Toghraie D (2022) Numerical study on the effect of solar radiation intensity on the fresh water productivity of solar still equipped with Thermoelectric Cooling System (TEC) for hot and dry areas of Semnan. Case Stud Therm Eng 32: 101848. https://doi.org/10.1016/j.csite.2022.101848 doi: 10.1016/j.csite.2022.101848
[22]	Sheikholeslami M, Said Z, Jafaryar M (2022) Hydrothermal analysis for a parabolic solar unit with wavy absorber pipe and nanofluid. Renewable Energy 188: 922-932. https://doi.org/10.1016/j.renene.2022.02.086 doi: 10.1016/j.renene.2022.02.086
[23]	Abd Al-wahid WA, Saad HA, Hasan ZH, et al. (2022) Experimental study of the performance of hemispherical solar still with optimum value of rocks as heat transfer enhancers. AIMS Energy 10: 885-899. https://doi.org/10.3934/energy.2022040 doi: 10.3934/energy.2022040
[24]	Kabeel AE, Abdelgaied M, Mahmoud GM (2021) Performance evaluation of continuous solar still water desalination system. J Therm Anal Calorim 144: 907-916. https://doi.org/10.1007/s10973-020-09547-5 doi: 10.1007/s10973-020-09547-5
[25]	Park CD, Lim BJ, Chung KY, et al. (2016) Experimental evaluation of hybrid solar still using waste heat. Desalination 379: 1-9. https://doi.org/10.1016/j.desal.2015.10.004 doi: 10.1016/j.desal.2015.10.004
[26]	Sohani A, Hoseinzadeh S, Samiezadeh S, et al. (2022) Machine learning prediction approach for dynamic performance modeling of an enhanced solar still desalination system. J Therm Anal Calorim 147: 3919-3930. https://doi.org/10.1007/s10973-021-10744-z doi: 10.1007/s10973-021-10744-z
[27]	Tuly SS, Sarker MRI, Das BK, et al. (2021) Effects of design and operational parameters on the performance of a solar distillation system: A comprehensive review. Groundwater Sustainable Dev 14: 100599. https://doi.org/10.1016/j.gsd.2021.100599 doi: 10.1016/j.gsd.2021.100599
[28]	Singh AK, Yadav RK, Mishra D, et al. (2020) Active solar distillation technology: A wide overview. Desalination 493: 114652. https://doi.org/10.1016/j.desal.2020.114652 doi: 10.1016/j.desal.2020.114652
[29]	Lee HS (2017) Thermoelectrics: Design and Materials, 1st ed., Mishigan: John Wiley & Sons. Available from: https://doi.org/.
[30]	Riffat SB, Ma X (2003) Thermoelectrics: A review of present and potential applications. Appl Therm Eng 23: 913-935. https://doi.org/10.1016/S1359-4311(03)00012-7 doi: 10.1016/S1359-4311(03)00012-7
[31]	Duan M, Sun H, Lin B, et al. (2021) Evaluation on the applicability of thermoelectric air cooling systems for buildings with thermoelectric material optimization. Energy 221: 119723. https://doi.org/10.1016/j.energy.2020.119723 doi: 10.1016/j.energy.2020.119723
[32]	Shen ZG, Tian LL, Liu X (2019) Automotive exhaust thermoelectric generators: Current status, challenges and future prospects. Energy Convers Manage 195: 1138-1173. https://doi.org/10.1016/j.enconman.2019.05.087 doi: 10.1016/j.enconman.2019.05.087
[33]	Liu Z, Li W, Zhang L, et al. (2019) Experimental study and performance analysis of solar-driven exhaust air thermoelectric heat pump recovery system. Energy Build 186: 46-55. https://doi.org/10.1016/j.enbuild.2019.01.017 doi: 10.1016/j.enbuild.2019.01.017
[34]	Siddique ARM, Muresan H, Majid SH, et al. (2019) An adjustable closed-loop liquid-based thermoelectric electronic cooling system for variable load thermal management. Therm Sci Eng Prog 10: 245-252. https://doi.org/10.1016/j.tsep.2019.02.004 doi: 10.1016/j.tsep.2019.02.004
[35]	Liu W, Hu J, Zhang S, et al. (2017) New trends, strategies and opportunities in thermoelectric materials: A perspective. Mater Today Phys 1: 50-60. https://doi.org/10.1016/j.mtphys.2017.06.001 doi: 10.1016/j.mtphys.2017.06.001
[36]	Phadatare MK, Verma SK (2007) Influence of water depth on internal heat and mass transfer in a plastic solar still. Desalination 217: 267-275. https://doi.org/10.1016/j.desal.2007.03.006 doi: 10.1016/j.desal.2007.03.006
[37]	de Garayo SD, Martínez A, Aranguren P, et al. (2021) Prototype of an air to air thermoelectric heat pump integrated with a double flux mechanical ventilation system for passive houses. Appl Therm Eng 190: 116801. https://doi.org/10.1016/j.applthermaleng.2021.116801 doi: 10.1016/j.applthermaleng.2021.116801

Reader Comments

Your name:*

Email:*
© 2023 the Author(s), licensee AIMS Press. This is an open access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0)