
The return-to-play process' characteristics can vary by injury and sport type but are typically composed of phases of different durations, training targets, and intensities that gradually increase the physiological and mechanical load. In team sports, contact drills are a necessary part of the last phases of this process, and they should be planned using the optimal mechanical load. The present study investigated the external load and kinetic recovery in U19 soccer players performing 6vs6 and 3vs3 small-sided games. A global positioning system (GPS) measured external load metrics. The rate of perceived exertion (RPE) was registered at the end. Total quality of recovery (TQR) was collected at the beginning of the training session and after 24 h. Moreover, before and after the small-sided games (SSGs) and at 24 h, delayed-onset muscle soreness (DOMS) of the legs, sprinting time, and vertical jump height (CMJ) were collected. 6vs6 presented higher values in total distance low-, moderate-, high, and very-high-speed distance, and maximum speed (p < 0.05). However, 3vs3 showed higher number of sprints, acceleration, and deceleration at different intensities. Furthermore, no difference was shown in RPE. The effect of fatigue on sprint seems greater for 6vs6, showing an impairment persistent at 24 h (p < 0.05). Moreover, CMJ height was impaired after 6vs6 and at 24 h (p < 0.05) but did not change after 3vs3 (p > 0.05). DOMS values after SSGs and at 24 h were higher than baseline for both conditions (p < 0.05), while TQR decreased at 24 h in both conditions (p < 0.05). Based on our results, it seems that 6vs6, leading to a greater high-speed running distance, might cause a training load that needs more time to recover. This point may be crucial in a return-to-play process, especially when hamstring muscles are involved.
Citation: Roberto Modena, Federico Schena. External training load and performance recovery after small-sided games in soccer: Insights for return-to-play management[J]. AIMS Public Health, 2024, 11(1): 315-329. doi: 10.3934/publichealth.2024016
[1] | Dorra Djebbi-Simmons, Mohammed Alhejaili, Marlene Janes, Joan King, Wenqing Xu . Survival and inactivation of human norovirus GII.4 Sydney on commonly touched airplane cabin surfaces. AIMS Public Health, 2020, 7(3): 574-586. doi: 10.3934/publichealth.2020046 |
[2] | Terri Rebmann, Kristin D. Wilson, Travis Loux, Ayesha Z. Iqbal, Eleanor B. Peters, Olivia Peavler . Outcomes, Approaches, and Challenges to Developing and Passing a Countywide Mandatory Vaccination Policy: St. Louis County’s Experience with Hepatitis A Vaccine for Food Service Personnel. AIMS Public Health, 2016, 3(1): 116-130. doi: 10.3934/publichealth.2016.1.116 |
[3] | Christy Pu . The Influence of the Common Cold on Self-Rated Health: A Population-Based Study. AIMS Public Health, 2015, 2(3): 247-255. doi: 10.3934/publichealth.2015.3.247 |
[4] | Yenisetti SC, Muralidhara . Beneficial Role of Coffee and Caffeine in Neurodegenerative Diseases: A Minireview. AIMS Public Health, 2016, 3(2): 407-422. doi: 10.3934/publichealth.2016.2.407 |
[5] | S. J. Olshansky, L. Hayflick . The Role of the WI-38 Cell Strain in Saving Lives and Reducing Morbidity. AIMS Public Health, 2017, 4(2): 127-138. doi: 10.3934/publichealth.2017.2.127 |
[6] | Junji Takaya . Small for Gestational Age and Magnesium: Intrauterine magnesium deficiency may induce metabolic syndrome in later life. AIMS Public Health, 2015, 2(4): 793-803. doi: 10.3934/publichealth.2015.4.793 |
[7] | Viorica Munteanu, Antonella Petaccia, Nicolae Contecaru, Emanuele Amodio, Carlo Virginio Agostoni . Paediatric acute rheumatic fever in developed countries: Neglected or negligible disease? Results from an observational study in Lombardy (Italy). AIMS Public Health, 2018, 5(2): 135-143. doi: 10.3934/publichealth.2018.2.135 |
[8] | Sudip Bhattacharya, Amarjeet Singh . Phasing out of the Universal Mega Dose of Vitamin-A Prophylaxis to Avoid Toxicity. AIMS Public Health, 2017, 4(1): 38-46. doi: 10.3934/publichealth.2017.1.38 |
[9] | Ali Hussain Ansari, Saqib Hussain Ansari, Mubarak Jabeen Salman, Muhammad Usman Hussain Ansari, Rawshan Jabeen . A scoping review on the obstacles faced by beta thalassemia major patients in Pakistan- Matter of policy investment. AIMS Public Health, 2024, 11(4): 1105-1124. doi: 10.3934/publichealth.2024057 |
[10] | Katherine Karacaoglu, Calum F Leask . Staff views of a hospital at home model implemented in a Scottish care setting. AIMS Public Health, 2021, 8(3): 467-478. doi: 10.3934/publichealth.2021036 |
The return-to-play process' characteristics can vary by injury and sport type but are typically composed of phases of different durations, training targets, and intensities that gradually increase the physiological and mechanical load. In team sports, contact drills are a necessary part of the last phases of this process, and they should be planned using the optimal mechanical load. The present study investigated the external load and kinetic recovery in U19 soccer players performing 6vs6 and 3vs3 small-sided games. A global positioning system (GPS) measured external load metrics. The rate of perceived exertion (RPE) was registered at the end. Total quality of recovery (TQR) was collected at the beginning of the training session and after 24 h. Moreover, before and after the small-sided games (SSGs) and at 24 h, delayed-onset muscle soreness (DOMS) of the legs, sprinting time, and vertical jump height (CMJ) were collected. 6vs6 presented higher values in total distance low-, moderate-, high, and very-high-speed distance, and maximum speed (p < 0.05). However, 3vs3 showed higher number of sprints, acceleration, and deceleration at different intensities. Furthermore, no difference was shown in RPE. The effect of fatigue on sprint seems greater for 6vs6, showing an impairment persistent at 24 h (p < 0.05). Moreover, CMJ height was impaired after 6vs6 and at 24 h (p < 0.05) but did not change after 3vs3 (p > 0.05). DOMS values after SSGs and at 24 h were higher than baseline for both conditions (p < 0.05), while TQR decreased at 24 h in both conditions (p < 0.05). Based on our results, it seems that 6vs6, leading to a greater high-speed running distance, might cause a training load that needs more time to recover. This point may be crucial in a return-to-play process, especially when hamstring muscles are involved.
global positioning system;
total quality of recovery;
delayed onset muscular soreness;
rate of perceived exertion;
total distance covered;
low-speed distance;
moderate-speed distance;
high-speed distance;
very high-speed distance;
countermovement jump
As the requirements facing batteries increase—both in terms of demand and complexity—the ability to understand, control, and predict battery performance becomes ever more urgent. Given the importance of the thermal effect on batteries’ behaviors with respect to a wide range of battery properties, including performance, life span, and—critically—safety, it would seem axiomatic that characterization of battery thermal profiles (particularly with respect to thermal monitoring during cycling) is a crucial part of battery development [1,2,3,4]. Indeed, relevant models, which range from simple one-dimensional thermal models to highly complex three-dimensional coupled thermal and electrochemical analyses, show that irrespective of device, non-uniform temperature distributions can be present during operation; often resulting in issues for the devices in question [5,6,7,8,9,10,11,12]. Moreover, due to the critical importance of safety, there has been considerable interest in developing and improving the thermal handling of battery systems—particularly with respect to that undertaken by the battery management system (BMS) [13,14,15,16].
This highlights the relevance of temperature with respect to operational and safety analyses for fuel cells and batteries, which is subsequently reflected in the varied and abundant literature produced regarding monitoring the thermal characteristics and behaviors of these devices [17,18,19,20]. Consequently, techniques appropriate for the elucidation of a greater understanding of these phenomena are in great demand. It should be no surprise, therefore, that thermal monitoring has become a popular area of research [21]. One increasingly popular analytical tool is infrared thermography (IT), as it is a safe, non-destructive, and contactless technology, which may be used to determine the thermal profile of a battery [20,21,22]. However, in addition to providing insights into the thermal profile of a battery (i.e. thermal monitoring) it must be noted that IT may also identify hotspots in situ (while the battery is still in operation) [21,23]. In many conventional battery systems, hotspots represent an indication of a fault and so, in this way, IT represents a powerful tool—capable not only of thermal monitoring but also the hitherto mostly neglected possibility [21,24] of early fault detection.
In general, nondestructive evaluation (NDE) by infrared thermography may be divided into two methods: 1) passive infrared thermography (PIT) and 2) active infrared thermography (AIT) [25]. In essence, PIT involves detecting abnormal temperature fields—the presence of which may indicate anomalies. This technique, mainly used for qualitative inspection and localization purposes, is relatively simple to implement and has been used to good effect for diagnosis in other fields [26]. By contrast, AIT consists of analyzing the transient heat flux of the thermal scene after its solicitation by an external thermal source, and has proven to be a powerful tool when PIT is too sensitive to variations of surrounding conditions, requires too long a duration, or does not provide sufficient thermal contrast [27]. While AIT does offer advantages over PIT, the simplicity of PIT makes it an ideal starting point for evaluation. Indeed, previous work has demonstrated that PIT in particular may be applied to lead acid batteries in order to successfully detect observable failures [24]. However, it also highlighted the difficulties in attempting to correlate voltage and thermal signal. This may be attributed to the complexities of the internal chemistries and design of the battery system making such attempts at direct correlation extremely challenging.
In order to address this issue, we believe that a refined approach may prove more viable. This may best be summarized as first correlating the battery’s thermal behavior—and formation of hotspots in particular—to the internal reactions, before using this understanding to develop the key descriptors for electrochemical performance prognosis with respect to early fault detection.
In this way, by linking the internal battery reaction to its thermal and electrical behavior, we suggest it will be possible to a) develop a non-destructive early fault monitoring technique; b) develop a refined thermal monitoring tool to ensure smooth and safe battery operation; and c) provide a framework of improved understanding to facilitate future iterative improvements.
However, in order to justify future development of this technique, it is first necessary to demonstrate the added value of such an approach. Thus, in order to validate our proposed technique as a proof-of-concept, we use—for the first time—a combination of in operando thermal imaging, electrochemical measurement, and post-mortem analysis to determine the utility and viability of the proposed technique.
In this work, we describe in detail our experimental methodology which consists of:
1) Gathering a dataset of thermal/electrochemical behaviors of pre-selected lead acid batteries.
2) Using PIT to identify key internal features of interest.
3) Undertaking post-mortem analyses to characterize these identified areas.
4) Correlating the batteries’ most relevant internal reactions to thermal behavior, so as to validate the utility of this approach.
5) Examining these proof-of-concept results with respect to applicability of this method to early fault detection in batteries.
Finally, we will summarize the results and discuss in detail the implications with regard to the on-going development of a fault detection model.
Two types of batteries were selected for analysis in this work: systems which are at the beginning-of-life (henceforth ‘BoL systems’), having undergone formation cycles only, and systems which have undergone field aging resulting from use in real-world telecommunications powerplant (henceforth ‘degraded systems’).
These batteries consist of a series of 6 cells, each of which has a grid of alternately 4 anode and 3 cathode plates, each insulated by a glass fiber separator impregnated with electrolyte (see schematic in Figure 1).
The two selected batteries were placed in a climate chamber, controlled by an Omron E5CC temperature controller, with padded walls to limit environmental reflections (Figure 2). The electrochemical tests were carried out using an Arbin LBT22043 cycler. The cycler’s ADC (analog to digital converter) has 24 bit resolution, and was configured to acquire data every minute.
Both batteries were left at room temperature, in the chamber, until thermal equilibrium with the environment was achieved.
After this period of thermal stabilization, the following protocol was simultaneously applied to both batteries:
● Discharge at 0.1C (−0.45 A) until the voltage reached 10.8 V
● A subsequent 2 h rest step
● Charge at 0.3C (1.35 A) under constant current until the voltage reached 14.7 V
● Charge at 14.7 V (constant voltage) until current is 0, 01C (0,045 A)
● Subsequently, a floating mode at 13.6 V for 7.5 hours
During the cycling procedure, the thermal behaviors of the two batteries were simultaneously measured using a FLIR A6752SC infrared camera (3–5 µm, 50 mm, f/2.5 lens). This infrared camera was controlled using the FLIR ResearchIR Max software (Version 4.40.9.30). To ensure thermal data was collected at times in accordance with the electrochemical data, thermal images were acquired every minute.
After selection of the appropriate area for measurement (as denoted in Figure 3b), the total thermal scene was represented by images of size 320 × 256 pixels (Figure 3a). The experimental thermograms were calculated by averaging, at each time step, of two zones of the thermal scene (131 × 91 pixels per battery, see Figure 3b).
The recorded data was post-treated using the FLIR ResearchIR Max software and the scientific programming language GNU Octave [28].
Post-mortem analysis was then carried out on relevant samples extracted from the battery. Crystallization was characterized using Scanning Electron Microscope (SEM) FEI Quanta 250. The crystal structures of the lead species present were then identified by X-ray diffraction (XRD) using a Bruker D8 Discover diffractometer (monochromatic Cu Kα radiation, λ = 1.54053 Å), at room temperature, within the 2θ range of 15 −80°.
From the body of experimental data, representative results were selected for characterization. Figure 4 shows the thermal scene at different times during the experiment (total duration c.a. 25 hours).
As expected, the use of passive infrared thermography allowed to detect the damaged battery by means of its excessive energy release (Figure 4, right side). One can notice that the results (images) are given in the arbitrary units of the infrared camera, proportional to the received radiative flux (an excessive energy release appears in yellow in the previous figure). Then, experimental thermograms were calculated for each battery (see 2.2. Experimental setup and protocol). These thermograms were obtained after conversion into apparent temperature using the internal calibration of the infrared camera and by arbitrarily fixing the emissivity of the thermal scene at 0.92. They were also corrected to take into account the variation in temperature of the environment (± 0.7 ℃).
The thermograms and the corresponding currents are plotted as a function of time in Figure 5.
At the end of the experiment (t > 70000 s), an infrared image was taken at each side of the degraded battery. By applying a simple thresholding treatment, the localization of the defective area is easily observed (see Figure 6).
It should also be noted that the quantitative study of the most emitting zones can provide a powerful tool to refine this location. Indeed, the amplitude of its thermal imprint on a given surface of a battery, as well as its diffusive spread, made it possible to estimate the probable location of a defect. Thus, in the case of the damaged battery studied in this paper, a weaker thermal diffusion observed on the ‘left and lower’ (Figure 6) faces indicate the proximity of the energy source. In the same way, the higher amplitude of the signal on the ‘left’ face indicated that the heat source is located near this face. Finally, by exploiting the data of the four faces, the probable location of the defect has been proposed (Figure 6, center). In order to validate the relevance of this approach a post-mortem study was conducted on the defective battery.
In order to ensure relevant post-mortem information was obtained for the aged battery, the points of interest were identified using detailed thermal mapping (see Figure 7). As can be seen, the area is located in upper part of block A, between cell 2 and 3.
In order to physically access this location, the battery was opened in a well-ventilated fume cupboard using Dremel cutting tools in accordance with safety protocols to ensure good laboratory practice.
Visual inspection (see Figure 8) revealed the anode plate was covered in molten plastic, the area of which corresponded with the estimated defect location. The 3D shape of the effect was, therefore, in good accordance with the highest temperature observed in the hot spot (as identified in the thermal images).
Upon opening the cell, a more in-depth post-mortem analysis was carried out, including taking XRD and SEM data of areas both in and out of the hotspot (see Figure 9).
Comparison of the XRD (Figure 9a) data to Pb [29] and PbSO4 [30] standards, confirms both are present in both the anode up and down regions. Examination of the SEM data (Figure 9b) reveals some significant difference, however—while the PbSO4 is present at the anode down as small, high solubility crystals, at the anode up region (i.e., at the hotspot) it is present as large, low solubility crystals. The post-mortem analysis of this data, carried out in the discussion section, both explains the results and proposes the mechanism responsible.
Examination of the thermal and electrochemical profiles of the batteries (see Figure 5) reveals important information even prior to post-mortem analysis. As can be seen, there is a strong correlation between the current charge/discharge profile and the thermal response for both systems. However, significant differences between the BoL and degraded systems may also be observed. The electrochemical profile of the BoL system followed the typical charge/discharge profile (as described in the manufacturer specifications), and the thermal response showed the expected time shift. By contrast, the degraded system not only exhibited a failed floating mode charge profile, but also an atypically high thermal profile. The combination of this abnormal behavior enabled easy identification of undesirable internal reactions within the battery. In short, comparison of the behaviors of these systems clearly demonstrates the value of this combined electrochemical-thermal analyses as a detection method for identifying areas of interest for in-depth post-mortem characterization.
Given the importance of understanding the effect of the batteryxs internal heat generation in order to optimize the systemxs design, it is important to identify which potential failure mode occurred. The failure modes of lead acid batteries are well reported in the literature [31,32], and include:
● Hard/irreversible sulfation—While PbSO4 is a normal product of a discharge at both electrodes, with aging of the battery irreversible sulfation occurs [33]. In essence, the formation of large, insoluble crystals leads to a build-up in their presence and loss of contact between plate and electrolyte, leading to permanent capacity reduction and increased internal resistance.
● Positive grid corrosion—positive plate/battery post (usually near the connection to the casing) corrosion restricts current flow, increases internal resistance due to PbOx passivation layer formation, and so leads to failure from blocked current or cracked casing [34].
● Electrolyte stratification—density differences leading to electrolyte separation during rest, resulting in inhomogeneous activity during charge/discharge, increased sulfation in areas with high concentration of acid, and—subsequently - increased wear [35].
● Water loss/desiccation—thermally induced evaporation and/or water splitting at high states of charge leading to electrolyte loss, inhomogeneous contact, and thus active and inactive regions leading to localized wear [36].
● Shedding—active mass is lost from the plates and collects at the bottom of the battery, which reduces the available active mass (and thus capacity) and—if sufficient mass collects—may cause a short circuit [37].
● Active mass degradation—chemical and physical changes in the active mass leading to loss of electrochemically active material and, subsequently, capacity [35].
These mechanisms are well known to result in loss of electrochemical performance within batteries used in stationary applications.
As seen from our XRD data (Figure 9a), the in-depth post-mortem analyses revealed the presence of PbSO4 crystals at both the anode up and down regions. This observation is, in fact, in accordance with characteristic aging of the battery, as formation of small, soluble, PbSO4 crystals is an inherent part of this process, and typically occurs via an Ostwald ripening mechanism [32].
The SEM data (Figure 9b), however, reveals some significant differences between the natures of the PbSO4 crystals at the anode up and down regions. While the crystals at the anode down region are the small, soluble PbSO4 crystals expected from the typical aging undergone by degraded systems, at the anode up region (the location of the hotspot) we see the large, insoluble, PbSO4 crystals associated with hard sulfation degradation [31].
This is a key point, particularly when combined with the visual inspection—which demonstrated dry regions in the anode up area, indicating water loss and desiccation. While determining the exact initial cause of the degradation would require further in-depth analyses beyond the scope of this work (and so are reserved for a future publication focusing on this topic), the information obtained from this combined post-mortem/thermal analysis alone is more than sufficient for us to propose that the following general processes are responsible:
a) Inhomogeneities in the electrolyte lead to dry regions which hinder PbSO4 from dissolving back into the electrolyte, essentially facilitating increased hard sulfation.
b) Recrystallization of PbSO4—from both normal aging and formation in dry regions—leads to the generation of large, insoluble PbSO4 crystals. The build up of these crystals increases localized internal resistance, leading to localized regions of increased temperature.
c) Localized increases in thermal activity (e.g., the hotspot observed by the thermal imaging) can lead to localized water loss, and increases in inhomogeneities in the electrolyte and hard sulfation.
Given that these processes are self-reinforcing, it seems reasonable to assume that the combination led to sufficient hard sulfation degradation and loss of contact as to explain the failure of the battery observed in the electrochemistry. Consequently, we can see there is a strong link between the thermal, physical, chemical, and electrochemical responses observed. Indeed, given the strong link between thermal response and generation of insoluble PbSO4 crystals (hard sulfation), we can tentatively propose that such thermal analyses may well enable detection of the degradation mechanism prior to system failure—i.e., a pathway to early fault detection.
This, therefore, represents a strong demonstration of our proposed refined methodology incorporating thermal, physical, chemical, and electrochemical analyses. This not only validates our approach, but also provides a strong framework for future characterization and development of analytical methodologies.
In summary, we have proposed using the correlation between internal battery physiochemistry and infrared thermography as a foundation for electrochemistry prognosis. This methodology not only offers facile, early fault detection, but also provides information regarding areas of interest (enabling rational selection of those areas so as to facilitate rapid diagnosis and evaluation). Validation of the link between thermal images and internal battery reactions has been successfully undertaken through a combination of in operando PIT and ex operando post-mortem characterization. This demonstrates the usefulness of the proposed methodology with respect towards developing early fault detection and—potentially—the knowledgebase and framework of understanding key to facilitating the rational iterative improvement of batteries.
Nevertheless, some challenges remain before consideration may be given towards utilization in real-world applications. Firstly, in order to gain the most benefit from this work, it will be necessary to extend validation towards other battery systems. Only by generating a sufficiently encompassing dataset will full utilization of this approach become possible. Secondly, the specific set-up used during this validation did require a degree of free space, the repositioning of the battery in order to generate data from all four sides, and required careful selection of infrared camera. However, it is worth noting that the spatial issues will be less problematic in accumulator rooms, where it is possible to achieve sufficient distance between the batteries and the camera. Moreover, the continuing rapid development of infrared imaging technology, combined with advances in determination of feature significance, would seem to suggest that in the near future improved contactless monitoring will be possible with readily available systems. It would seem reasonable to conclude, therefore, that neither of these challenges represents an obstacle to continuing work in this area.
Meanwhile, by demonstrating clearly that there is an advantage to the novel approach of combined post-mortem data and thermal imaging technologies for battery analysis, here carried out for the first time, we take an important first step towards enhancing the characterization of battery systems in general, as well as representing a strong foundation for future analytical and safety investigations. This would not only be a significant advance for the field in and of itself, but also will be key to the development of remote monitoring of batteries and automated validation—particularly with respect to predicative modelling of performance.
The authors would like to express their gratitude to Joseba Segura for his support regarding the operation of the battery cycler, and his technical and scientific contributions to this work.
The authors declare no conflicts of interest.
[1] |
López-Valenciano A, Ruiz-Pérez I, Garcia-Gómez A, et al. (2020) Epidemiology of injuries in professional football: a systematic review and meta-analysis. Br J Sports Med 54: 711-718. https://doi.org/10.1136/bjsports-2018-099577 ![]() |
[2] |
Robles-Palazón FJ, López-Valenciano A, De Ste Croix M, et al. (2021) Epidemiology of injuries in male and female youth football players: A systematic review and meta-analysis. J Sport Health Sci 11: 681-695. https://doi.org/10.1016/j.jshs.2021.10.002 ![]() |
[3] |
Eirale C, Tol JL, Farooq A, et al. (2013) Low injury rate strongly correlates with team success in Qatari professional football. Br J Sports Med 47: 807-808. https://doi.org/10.1136/bjsports-2012-091040 ![]() |
[4] |
Hägglund M, Waldén M, Magnusson H, et al. (2013) Injuries affect team performance negatively in professional football: an 11-year follow-up of the UEFA Champions League injury study. Br J Sports Med 47: 738-742. https://doi.org/10.1136/bjsports-2013-092215 ![]() |
[5] |
Ardern CL, Glasgow P, Schneiders A, et al. (2016) 2016 Consensus statement on return to sport from the First World Congress in Sports Physical Therapy, Bern. Br J Sports Med 50: 853-864. https://doi.org/10.1136/bjsports-2016-096278 ![]() |
[6] |
Lemes IR, Pinto RZ, Lage VN, et al. (2021) Do exercise-based prevention programmes reduce non-contact musculoskeletal injuries in football (soccer)? A systematic review and meta-analysis with 13 355 athletes and more than 1 million exposure hours. Br J Sports Med 55: 1170-1178. https://doi.org/10.1136/bjsports-2020-103683 ![]() |
[7] |
Hodgson C, Akenhead R, Thomas K (2014) Time-motion analysis of acceleration demands of 4v4 small-sided soccer games played on different pitch sizes. Hum Mov Sci 33: 25-32. https://doi.org/10.1016/j.humov.2013.12.002 ![]() |
[8] |
Kelly DM, Drust B (2009) The effect of pitch dimensions on heart rate responses and technical demands of small-sided soccer games in elite players. J Sci Med Sport 12: 475-479. https://doi.org/10.1016/j.jsams.2008.01.010 ![]() |
[9] |
Riboli A, Coratella G, Rampichini S, et al. (2020) Area per player in small-sided games to replicate the external load and estimated physiological match demands in elite soccer players. PLoS One 15: e0229194. https://doi.org/10.1371/journal.pone.0229194 ![]() |
[10] |
Köklü Y, Sert Ö, Alemdaroğlu U, et al. (2015) Comparison of the Physiological Responses and Time-Motion Characteristics of Young Soccer Players in Small-Sided Games: The effect of goalkeeper. J Strength Cond Res 29: 964-971. https://doi.org/10.1519/JSC.0b013e3182a744a1 ![]() |
[11] |
Modena R, Togni A, Fanchini M, et al. (2021) Influence of pitch size and goalkeepers on external and internal load during small-sided games in amateur soccer players. Sport Sci Health 17: 797-805. https://doi.org/10.1007/s11332-021-00766-3 ![]() |
[12] |
Rampinini E, Impellizzeri FM, Castagna C, et al. (2007) Factors influencing physiological responses to small-sided soccer games. J Sports Sci 25: 659-666. https://doi.org/10.1080/02640410600811858 ![]() |
[13] | Katis A, Kellis E (2009) Effects of small-sided games on physical conditioning and performance in young soccer players. J Sports Sci Med 8: 374-380. |
[14] |
Rebelo NAC, Silva P, Rago V, et al. (2016) Differences in strength and speed demands between 4v4 and 8v8 small-sided football games. J Sports Sci 34: 2246-2254. https://doi.org/10.1080/02640414.2016.1194527 ![]() |
[15] |
Papanikolaou K, Tsimeas P, Anagnostou A, et al. (2021) Recovery Kinetics Following Small-Sided Games in Competitive Soccer Players: Does Player Density Size Matter?. Int J Sports Physiol Perform 16: 1270-1280. https://doi.org/10.1123/ijspp.2020-0380 ![]() |
[16] |
Bizzini M, Impellizzeri FM, Dvorak J, et al. (2013) Physiological and performance responses to the ‘FIFA 11+’ (part 1): Is it an appropriate warm-up?. J Sports Sci 31: 1481-1490. https://doi.org/10.1080/02640414.2013.802922 ![]() |
[17] |
Huggins RA, Giersch GEW, Belval LN, et al. (2020) The validity and reliability of global positioning system units for measuring distance and velocity during linear and team sport simulated movements. J Strength Cond Res 34: 3070-3077. https://doi.org/10.1519/JSC.0000000000003787 ![]() |
[18] |
Kenttä G, Hassmén P (1998) Overtraining and recovery a conceptual model. Sports Med 26: 1-16. https://doi.org/10.2165/00007256-199826010-00001 ![]() |
[19] | Flaherty SA (1996) Pain measurement tools for clinical practice and research. AANA J 64: 133-140. |
[20] |
Borg E, Borg G (2002) A comparison of AME and CR100 for scaling perceived exertion. Acta Psychol 109: 157-175. https://doi.org/10.1016/s0001-6918(01)00055-5 ![]() |
[21] |
Altmannid S, Ringhof S, Neumann R, et al. (2019) Validity and reliability of speed tests used in soccer: A systematic review. PLoS One 14: e0220982. https://doi.org/10.1371/journal.pone.0220982 ![]() |
[22] |
Glatthorn JF, Gouge S, Nussbaumer S, et al. (2011) Validity and reliability of optojump photoelectric cells for estimating vertical jump height. J Strength Cond Res 25: 556-560. https://doi.org/10.1519/JSC.0b013e3181ccb18d ![]() |
[23] |
Lakens D (2013) Calculating and reporting effect sizes to facilitate cumulative science: A practical primer for t-tests and ANOVAs. Front Psychol 4: 863. https://doi.org/10.3389/fpsyg.2013.00863 ![]() |
[24] | Cohen J (1988) Statistical power analysis for the behavioral sciences. Routledge: . https://doi.org/10.4324/9780203771587 |
[25] |
Gaudino P, Alberti G, Iaia FM (2014) Estimated metabolic and mechanical demands during different small-sided games in elite soccer players. Hum Mov Sci 36: 123-133. https://doi.org/10.1016/j.humov.2014.05.006 ![]() |
[26] |
Hader K, Rumpf MC, Hertzog M, et al. (2019) Monitoring the athlete match response: Can external load variables predict post-match acute and residual fatigue in soccer? A systematic review with meta-analysis. Sports Med Open 5: 48. https://doi.org/10.1186/s40798-019-0219-7 ![]() |
[27] | Teixeira JE, Forte P, Ferraz R, et al. (2022) The association between external training load, perceived exertion and total quality recovery in sub-elite youth football. Open Sports Sci J . https://doi.org/10.2174/1875399X-v15-e2207220 |
[28] |
Teixeira JE, Forte P, Ferraz R, et al. (2021) Quantifying sub-elite youth football weekly training load and recovery variation. Appl Sci 11: 4871. https://doi.org/10.3390/app11114871 ![]() |
[29] |
Madison G, Patterson SD, Read P, et al. (2019) Effects of small-sided game variation on changes in hamstring strength. J Strength Cond Res 33: 839-845. https://doi.org/10.1519/JSC.0000000000002955 ![]() |
[30] |
Saw AE, Main LC, Gastin PB (2016) Monitoring the athlete training response: Subjective self-reported measures trump commonly used objective measures: A systematic review. Br J Sports Med 50: 281-291. https://doi.org/10.1136/bjsports-2015-094758 ![]() |
1. | He-Teng Zhang, Hao Wang, Hai-Sheng Wu, Jian Zeng, Yan Yang, Comparison of viromes in vaginal secretion from pregnant women with and without vaginitis, 2021, 18, 1743-422X, 10.1186/s12985-020-01482-z | |
2. | Yalda Lucero, David O. Matson, Shai Ashkenazi, Sergio George, Miguel O’Ryan, Norovirus: Facts and Reflections from Past, Present, and Future, 2021, 13, 1999-4915, 2399, 10.3390/v13122399 | |
3. | Syafruddin Ilyas, Salomo Hutahaean, Putri Cahaya Sit, Analysis of Cytochrome c Expression on Liver Histology of Hepatitis Rats after Administration of Tin and Olive Leaf Ethanol Extract, 2022, 25, 10288880, 835, 10.3923/pjbs.2022.835.842 | |
4. | Louisa F. Ludwig-Begall, Axel Mauroy, Etienne Thiry, Noroviruses—The State of the Art, Nearly Fifty Years after Their Initial Discovery, 2021, 13, 1999-4915, 1541, 10.3390/v13081541 | |
5. | Prashasti Sinha, Anil Kumar Yadav, Theoretical Study of Azetidine Derivative by Quantum Chemical Methods, Molecular Docking and Molecular Dynamic Simulations, 2023, 8, 2365-6549, 10.1002/slct.202300190 | |
6. | Rabab Taha, Noura Elazhary, Sarah Alqhtani, Walaa Almansouri, Fatal Acute Liver Failure Following Norovirus Gastroenteritis in a Child: A Case Report, 2025, 18760341, 102675, 10.1016/j.jiph.2025.102675 |