Search Advanced

AIMS Materials Science

2020, Volume 7, Issue 5: 684-704. doi: 10.3934/matersci.2020.5.684
Previous Article Next Article
Review Topical Sections

A comprehensive review of recent progress in fabrication of magnesium base composites by friction stir processing technique—A review

  • 1.
    Research Scholar, I.K. Gujral Punjab Technical University, Kapurthala, India
  • 2.
    Department of Mechanical Engineering, I.K. Gujral Punjab Technical University, Kapurthala, India
  • Received: 25 August 2020 Accepted: 19 October 2020 Published: 23 October 2020

  • Metal matrix composites (MMCs) are the next generation materials, globally popular for having numerous potential applications in aircraft, automobile and biomedical industry. Magnesium being continuously replacing other conventional materials however it is a hard to process material. Recently, friction stir processing (FSP) is drawing attention among researchers to fabricate MMCs. Using FSP, superior properties of magnesium based MMCs being successfully achieved. The primary aim of this paper is to review and provide a thorough summary of FSP synthesized magnesium based composites. Additionally the effect of secondary phase particles on the tribological behavior of produced composite materials is also summed up. Mechanical along with microstructural properties produced from stirred process and contribution of strengthening mechanism is addressed, as well.

    Citation: P. Sagar, A. Handa. A comprehensive review of recent progress in fabrication of magnesium base composites by friction stir processing technique—A review[J]. AIMS Materials Science, 2020, 7(5): 684-704. doi: 10.3934/matersci.2020.5.684

    Related Papers:

  • Metal matrix composites (MMCs) are the next generation materials, globally popular for having numerous potential applications in aircraft, automobile and biomedical industry. Magnesium being continuously replacing other conventional materials however it is a hard to process material. Recently, friction stir processing (FSP) is drawing attention among researchers to fabricate MMCs. Using FSP, superior properties of magnesium based MMCs being successfully achieved. The primary aim of this paper is to review and provide a thorough summary of FSP synthesized magnesium based composites. Additionally the effect of secondary phase particles on the tribological behavior of produced composite materials is also summed up. Mechanical along with microstructural properties produced from stirred process and contribution of strengthening mechanism is addressed, as well.


    加载中


    [1] Smith W, Hashemi J, Prakash R (2008) Materials Science and Engineering (SIE), 4 Eds., New York: McGraw Hill Education.
    [2] Clyne TW, Hull D (2019) An Introduction to Composite Materials, 3 Eds., Cambridge: Cambridge University Press.
    [3] Van Suchtelen J (1972) Product properties: a new application of composite materials. Philips Res Rep 27: 28-37.
    [4] Chung DDL (2010) Composite Materials Science and Applications, 2 Eds., New York: Springer.
    [5] Mukhin I, Perevezentsev E, Palashov O (2014) Fabrication of composite laser elements by a new thermal diffusion bonding method. Opt Mater Express 4: 266-271.
    [6] Bodukuri AK, Eswaraiah K, Rajendar K, et al. (2016) Fabrication of Al-SiC-B4C metal matrix composite by powder metallurgy technique and evaluating mechanical properties. Perspect Sci 8: 428-431.
    [7] Jiang QC, Wang HY, Ma BX, et al. (2005) Fabrication of B4C particulate reinforced magnesium matrix composite by powder metallurgy. J Alloy Compd 386: 177-181.
    [8] Schubert T, Trindade B, Weißgärber T, et al. (2008) Interfacial design of Cu-based composites prepared by powder metallurgy for heat sink applications. Mat Sci Eng A-Struct 475: 39-44.
    [9] Wang X, Jha A, Brydson R (2004) In situ fabrication of Al3Ti particle reinforced aluminium alloy metal-matrix composites. Mat Sci Eng A-Struct 364: 339-345.
    [10] Yang B, Wang F, Zhang JS (2003) Microstructural characterization of in situ TiC/Al and TiC/Al-20Si-5Fe-3Cu-1Mg composites prepared by spray deposition. Acta Mater 51: 4977-4989.
    [11] Hashim J, Looney L, Hashmi MSJ (1999) Metal matrix composites: production by the stir casting method. J Mater Process Tech 92: 1-7.
    [12] Uozumi H, Kobayashi K, Nakanishi K, et al. (2008) Fabrication process of carbon nanotube/light metal matrix composites by squeeze casting. Mat Sci Eng A-Struct 495: 282-287.
    [13] Hu H (1998) Squeeze casting of magnesium alloys and their composites. J Mater Sci 33: 1579-1586.
    [14] Dhanashekar M, Kumar VSS (2014) Squeeze casting of aluminium metal matrix composites—An overview. Procedia Eng 97: 412-420.
    [15] He CN, Zhao NQ, Shi CS, et al. (2009) Mechanical properties and microstructures of carbon nanotube-reinforced Al matrix composite fabricated by in situ chemical vapor deposition. J Alloys Compd 487: 258-262.
    [16] Delhaes P (2002) Chemical vapor deposition and infiltration processes of carbon materials. Carbon 40: 641-657.
    [17] Mishra RS, Ma ZY (2005) Friction stir welding and processing. Mat Sci Eng R 50: 1-78.
    [18] Meng X, Huang Y, Cao J, et al. (2020) Recent progress on control strategies for inherent issues in friction stir welding. Prog Mater Sci 115: 100706.
    [19] Sharma V, Prakash U, Kumar BVM (2018) Surface composites by friction stir processing: A review. J Mater Process Tech 224: 117-134.
    [20] Ni DR, Wang JJ, Zhou ZN, et al. (2014) Fabrication and mechanical properties of bulk NiTip/Al composites prepared by friction stir processing. J Alloys Compd 586: 368-374.
    [21] Thangarasu A, Murugan N, Dinaharan I, et al. (2015) Synthesis and characterization of titanium carbide particulate reinforced AA6082 aluminium alloy composites via friction stir processing. Arch Civ Mech Eng 15: 324-334.
    [22] Salehi M, Farnoush H, Mohandesi JA (2014) Fabrication and characterization of functionally graded Al-SiC nanocomposite by using a novel multistep friction stir processing. Mater Design 63: 419-426.
    [23] Byung-Wook AHN, Don-Hyun C, Yong-Hwan KIM, et al. (2012) Fabrication of SiCp/AA5083 composite via friction stir welding. T Nonferr Metal Soc 22: s634-s638.
    [24] Sagar P, Handa A (2020) Selection of tool transverse speed considering trial run experimentations for AZ61/Tic composite developed via friction stir processing using triangular tool. Mater Today Proc In press.
    [25] Guo J, Amira S, Gougeon P, et al. (2011) Effect of the surface preparation techniques on the EBSD analysis of a friction stir welded AA1100-B4C metal matrix composite. Mater Charact 62: 865-877.
    [26] Yang M, Xu C, Wu C, et al. (2010) Fabrication of AA6061/Al2O3 nano ceramic particle reinforced composite coating by using friction stir processing. J Mater Sci 45: 4431-4438.
    [27] Feng AH, Ma ZY (2007) Formation of Cu2FeAl7 phase in friction-stir-welded SiCp/Al-Cu-Mg composite. Scripta Mater 57: 1113-1116.
    [28] Lim DK, Shibayanagi T, Gerlich AP (2009) Synthesis of multi-walled CNT reinforced aluminium alloy composite via friction stir processing. Mat Sci Eng A-Struct 507: 194-199.
    [29] Gupta M, Ling MN (2011) Magnesium, Magnesium Alloys and Magnesium Composites, 1 Ed., Hoboken: John Wiley and Sons.
    [30] Sunil BR, Reddy GPK, Patle H, et al. (2016) Magnesium based surface metal matrix composites by friction stir processing. J Magnes Alloy 4: 52-61.
    [31] Mishra RS, Mahoney MW, McFadden SX, et al. (1999) High strain rate superplasticity in a friction stir processed 7075Al alloy. Scripta Mater 42: 163-168.
    [32] Dinaharan I, Murugan N, Parameswaran S (2012) Developing an empirical relationship to predict the influence of process parameters on tensile strength of friction stir welded AA6061/0-10 wt% ZrB2 in situ composite. Trans Indian Inst Met 65: 159-170.
    [33] Dolatkhah A, Golbabaei P, Givi MKB, et al. (2012) Investigating effects of process parameters on microstructural and mechanical properties of Al5052/SiC metal matrix composite fabricated via friction stir processing. Mater Design 37: 458-464.
    [34] Zohoor M, Givi MKB, Salami P (2012) Effect of processing parameters on fabrication of Al-Mg/Cu composites via friction stir processing. Mater Design 39: 358-365.
    [35] Thangarasu A, Murugan N, Dinaharan I, et al. (2014) Influence of traverse speed on microstructure and mechanical properties of AA6082-TiC surface composite fabricated by friction stir processing. Procedia Mater Sci 5: 2115-2121.
    [36] Bauri R, Janaki Ram GD, Yadav D, et al. (2015) Effect of process parameters and tool geometry on fabrication of Ni particles reinforced 5083 Al composite by friction stir processing. Mater Today Proc 2: 3203-3211.
    [37] Patel VV, Badheka V, Kumar A (2016) Influence of friction stir processed parameters on superplasticity of Al-Zn-Mg-Cu alloy. Mater Manuf Process 31: 1573-1582.
    [38] Salehi M, Farnoush H, Mohandesi JA (2014) Fabrication and characterization of functionally graded Al-SiC nanocomposite by using a novel multistep friction stir processing. Mater Design 63: 419-426.
    [39] Hoda MDN, Singari RM, Arulmoni VJ (2016) Friction stir processing (FSP) of copper and enhancement of its mechanical properties using graphite powder. IJRSI 3: 58-65.
    [40] Sathiskumar R, Murugan N, Dinaharan I, et al. (2013) Prediction of mechanical and wear properties of copper surface composites fabricated using friction stir processing. Mater Design 55: 224-234.
    [41] Rathee S, Maheshwari S, Siddiquee AN, et al. (2018) A review of recent progress in solid state fabrication of composites and functionally graded systems via friction stir processing. Crit Rev Solid State 43: 334-366.
    [42] Li K, Liu X, Zhao Y (2019) Research status and prospect of friction stir processing technology. Coatings 9: 129.
    [43] Vijay SJ, Murugan N (2010) Influence of tool pin profile on the metallurgical and mechanical properties of friction stir welded Al-10 wt% TiB2 metal matrix composite. Mater Design 31: 3585-3589.
    [44] Zhang YN, Cao X, Larose S, et al. (2012) Review of tools for friction stir welding and processing. Can Metall Quart 51: 250-261.
    [45] Kirkland NT, Birbilis N (2014) Introduction to magnesium biomaterials, Magnesium Biomaterials, 1 Ed., Cham: Springer, 1-12.
    [46] Asadi P, Faraji G, Besharati MK (2010) Producing of AZ91/SiC composite by friction stir processing (FSP). Int J Adv Manuf Tech 51: 247-260.
    [47] Asadi P, Givi MKB, Faraji G (2010) Producing ultrafine-grained AZ91 from as-cast AZ91 by FSP. Mater Manuf Process 25: 1219-1226.
    [48] Faraji G, Dastani O, Asghar SA, et al. (2011) Effect of process parameters on microstructure and micro-hardness of AZ91/Al2O3 surface composite produced by FSP. J Mater Eng Perform 20: 1583-1590.
    [49] Khayyamin D, Mostafapour A, Keshmiri R (2013) The effect of process parameters on microstructural characteristics of AZ91/SiO2 composite fabricated by FSP. Mat Sci Eng A-Struct 559: 217-221.
    [50] Faraji G, Dastani O, Mousavi SAAA (2011) Microstructures and mechanical properties of Al2O3/AZ91 surface nanocomposite layer produced by friction stir processing. P I Mech Eng B-J Eng 225: 1331-1345.
    [51] Ahmadkhaniha D, Heydarzadeh Sohi M, Salehi A, et al. (2016) Formations of AZ91/Al2O3 nano-composite layer by friction stir processing. J Magnes Alloy 4: 314-318.
    [52] Dadashpour M, Mostafapour A, Yeşildal R, et al. (2016) Effect of process parameter on mechanical properties and fracture behavior of AZ91C/SiO2 composite fabricated by FSP. Mat Sci Eng A-Struct 655: 379-387.
    [53] Chen T, Zhu Z, Ma Y, et al. (2010) Friction stir processing of thixoformed AZ91D magnesium alloy and fabrication of surface composite reinforced by SiCps. J Wuhan Univ Technol 25: 223-227.
    [54] Singh N, Singh J, Singh B, et al. (2018) Wear behavior of B4C reinforced AZ91 matrix composite fabricated by FSP. Mater Today Proc 5: 19976-19984.
    [55] Morisada Y, Fujii H, Nagaoka T, et al. (2006) Effect of friction stir processing with SiC particles on microstructure and hardness of AZ31. Mat Sci Eng A-Struct 433: 50-54.
    [56] Morisada Y, Fujii H, Nagaoka T, et al. (2006) MWCNTs/AZ31 surface composites fabricated by friction stir processing. Mat Sci Eng A-Struct 419: 344-348.
    [57] Azizieh M, Kokabi AH, Abachi P (2011) Effect of rotational speed and probe profile on microstructure and hardness of AZ31/Al2O3 nanocomposites fabricated by friction stir processing. Mater Design 32: 2034-2041.
    [58] Azizieh M, Kim HS, Kokabi AH, et al. (2011) Fabrication of AZ31/Al2O3 nanocomposites by friction STIR processing. Rev Adv Mater Sci 28: 85-89.
    [59] Srinivasan M, Loganathan C, Balasubramanian V, et al. (2011) Feasibility of joining AZ31B magnesium metal matrix composite by friction welding. Mater Design 32: 1672-1676.
    [60] Chang CI, Wang YN, Pei HR, et al. (2007) Microstructure and mechanical properties of nano-ZrO2 and nano-SiO2 particulate reinforced AZ31-Mg based composites fabricated by friction stir processing. Key Eng Mater 351: 114-119.
    [61] Balakrishnan M, Dinaharan I, Palanivel R, et al. (2015) Synthesize of AZ31/TiC magnesium matrix composites using friction stir processing. J Magnes Alloy 3: 76-78.
    [62] Jiang Y, Yang X, Miura H, et al. (2013) Particles reinforced magnesium alloy produced by friction stir processing. Rev Adv Mater Sci 33: 29-32.
    [63] Sharma S, Handa A, Singh SS, et al. (2019) Synthesis of a novel hybrid nanocomposite of AZ31Mg-Graphene-MWCNT by multi-pass friction stir processing and evaluation of mechanical properties. Mater Res Express 6: 126531.
    [64] Huang Y, Wang T, Guo W, et al. (2014) Microstructure and surface mechanical property of AZ31 Mg/SiCp surface composite fabricated by direct friction stir processing. Mater Design 59: 274-278.
    [65] Soltani M, Shamanian M, Niroumand B (2015) Surface characteristics improvement of AZ31B magnesium by surface compositing with carbon nano-tubes through friction stir processing. Int J Adv Des Manuf Technol 8: 85-95.
    [66] Navazani M, Dehghani K (2015) Investigation of microstructure and hardness of Mg/TiC surface composite fabricated by friction stir processing (FSP). Procedia Mater Sci 11: 509-514.
    [67] Sunil BR, Kumar TSS, Chakkingal U, et al. (2014) Nano-hydroxyapatite reinforced AZ31 magnesium alloy by friction stir processing: A solid state processing for biodegradable metal matrix composites. J Mater Sci Mater Med 25: 975-988.
    [68] Sharma S, Handa A, Singh SS, et al. (2019) Influence of tool rotation speeds on mechanical and morphological properties of friction stir processed nano hybrid composite of MWCNT-Graphene-AZ31 magnesium. J Magnes Alloy 7: 487-500.
    [69] Das S, Mishra RS, Doherty KJ, et al. (2016) Magnesium based composite via friction stir processing, In: Mishra R, Mahoney MW, Sato Y, et al., Frict Stir Weld Process VII, Cham: Springer, 245-252.
    [70] Vedabouriswaran G, Aravindan S (2018) Development and characterization studies on magnesium alloy (RZ 5) surface metal matrix composites through friction stir processing. J Magnes Alloy 6: 145-163.
    [71] Del Valle JA, Rey P, Gesto D, et al. (2012) Friction stir processing of the magnesium alloy AZ61: Grain size refinement and mechanical properties. Mater Sci Forum 706: 1823-1828.
    [72] Lee CJ, Huang JC, Hsieh PJ (2006) Mg based nano-composites fabricated by friction stir processing. Scripta Mater 54: 1415-1420.
    [73] Du X, Wu B (2009) Using two-pass friction stir processing to produce nanocrystalline microstructure in AZ61 magnesium alloy. Sci China Technol Sci 52: 1751-1755.
    [74] Madhusudhan Reddy G, Sambasiva Rao A, Srinivasa Rao K (2013) Friction stir processing for enhancement of wear resistance of ZM21 magnesium alloy. Trans Indian Inst Met 66: 13-24.
    [75] Abbasi M, Bagheri B, Dadaei M, et al. (2015) The effect of FSP on mechanical, tribological, and corrosion behavior of composite layer developed on magnesium AZ91 alloy surface. Int J Adv Manuf Tech 77: 2051-2058.
    [76] Singh J, Lal H, Bala N (2013) Investigations on the wear behavior of friction stir processed magnesium based AZ91 alloy. Int J Mech Eng Robot Res 2: 271-274.
    [77] Arora HS, Singh H, Dhindaw BK, et al. (2012) Improving the tribological properties of mg based AZ31 alloy using friction stir processing. Adv Mater Res 585: 579-583.
    [78] Arora HS, Singh H, Dhindaw BK (2013) Wear behaviour of a Mg alloy subjected to friction stir processing. Wear 303: 65-77.
    [79] Ram B, Deepak D, Bala N (2019) Role of friction stir processing in improving wear behavior of Mg/SiC composites produced by stir casting route. Mater Res Express 6: 026577.
    [80] Azizieh M, Larki AN, Tahmasebi M, et al. (2018) Wear behavior of AZ31/Al2O3 magnesium matrix surface nanocomposite fabricated via friction stir processing. J Mater Eng Perform 27: 2010-2017.
    [81] Dinaharan I, Vettivel SC, Balakrishnan M, et al. (2019) Influence of processing route on microstructure and wear resistance of fly ash reinforced AZ31 magnesium matrix composites. J Magnes Alloy 7: 155-165.
    [82] Faraji G, Asadi P (2011) Characterization of AZ91/alumina nanocomposite produced by FSP. Mat Sci Eng A-Struct 528: 2431-2440.
    [83] Lu D, Jiang Y, Zhou R (2013) Wear performance of nano-Al2O3 particles and CNTs reinforced magnesium matrix composites by friction stir processing. Wear 305: 286-290.
    [84] Whang S (2011) Nanostructured metals and alloys, Woodhead Publishing Series in Metals and Surface Engineering, 1 Ed., Cambridge: Woodhead Publishing, 15-19.
    [85] Pande CS, Cooper KP (2009) Nanomechanics of Hall-Petch relationship in nanocrystalline materials. Prog Mater Sci 54: 689-706.
    [86] Sato YS, Urata M, Kokawa H, et al. (2003) Hall-Petch relationship in friction stir welds of equal channel angular-pressed aluminum alloys. Mat Sci Eng A-Struct 354: 298-305.
    [87] Xiao P, Gao Y, Yang C, et al. (2018) Microstructure, mechanical properties and strengthening mechanisms of Mg matrix composites reinforced with in situ nanosized TiB2 particles. Mat Sci Eng A-Struct 710: 251-259.
    [88] Hung YP, Huang JC, Wu KJ, et al. (2006) Strengthening and toughness of AZ61 Mg with nano SiO2 particles. Mater Trans 47: 1985-1993.
    [89] Zhang Z, Chen DL (2008) Contribution of Orowan strengthening effect in particulate-reinforced metal matrix nanocomposites. Mat Sci Eng A-Struct 483: 148-152.
    [90] Sanaty-Zadeh A (2012) Comparison between current models for the strength of particulate-reinforced metal matrix nanocomposites with emphasis on consideration of Hall-Petch effect. Mat Sci Eng A-Struct 531: 112-118.
    [91] Huang Y, Li J, Wan L, et al. (2018) Strengthening and toughening mechanisms of CNTs/Mg-6Zn composites via friction stir processing. Mat Sci Eng A-Struct 732: 205-211.
    [92] Bist A, Saini JS, Sharma B (2018) A review of tool wear prediction during friction stir welding of aluminium matrix composite. T Nonferr Metal Soc 26: 2003-2018.
    [93] Chen G, Zhang S, Zhu Y, et al. (2020) Thermo-mechanical analysis of friction stir welding: A review on recent advances. Acta Metall Sin Engl Lett 33: 3-12.
    [94] Kosturek R, Śnieżek L, Torzewski J, et al. (2019) Research on the friction stir welding of sc-modified AA2519 extrusion. Metals 9: 1024-1038.
    [95] Derazkola HA, Khodabakhshi F (2020) A novel fed friction-stir (FFS) technology for nanocomposite joining. Sci Technol Weld Joi 25: 89-100.
  • Reader Comments
  • © 2020 the Author(s), licensee AIMS Press. This is an open access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0)
通讯作者: 陈斌, bchen63@163.com
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索
AIMS Materials Science
1.4 3.6

Metrics

Article views(4892) PDF downloads(299) Cited by(18)

Preview PDF
Download XML
Export Citation
Article outline

Figures and Tables

Figures(9)  /  Tables(1)

Other Articles By Authors

Related pages

Tools

/

DownLoad:  Full-Size Img  PowerPoint
Return
Return

Catalog